1 using supplied hardware. 4. Connect the electrical wiring for power, illumination, and ground as shown in FIG. 1. Connect supplied data line to remote, route to the radio and connect to the connector on the rear of the radio as shown in FIG. 2. 2 AMP FUSE BLUE Data line (connect to radio) BLACK: ground YELLOW Illumination (connect to instrument lighting) RED + 12V switched/ignition A NUT LOCK WASHER WASHER cm MOUNTING SURFACE GASKET REMOTE FIG. 1 Note, The rear view of radio an

• The VOX Gain can be adjusted from levels 1 to 10 and OFF. • The transceiver announces the VOX Gain level as you adjust it. If OFF is selected, a beep sounds. 5 Press the PTT switch to save the setting. • A beep will sound. • The transceiver announces the new VOX Gain level. 6 Turn the transceiver power OFF and the ON again to activate VOX. Note: . If a speaker/ microphone is connected to the transceiver while the VOX function is switched ON and the VOX Gain level is configured to a higher, mor

Release the key to return to normal operation. 12 SCAN Scan is useful for monitoring signals on the transceiver channels. When scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. The transceiver will remain on a busy channel until the signal is no longer present. Your dealer programs the delay time between signal drop-out and Scan resumption. If a signal is received during the delay time, the transceiver will remain on the same channel. Note: You

Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally while transmitting. PREPARATION PREPARATION Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. TOOLS REQUIRED Note: Before installing

FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Note: This function is available only in Conventional FM Operation. KEY FUNCTIONS Key Function Selcall or Selcall + Status Press to change the transceiver mode as shown in the diagram below. CH control Rotate to select an ID from the pre-programmed ID list or Status list. PTT switch or PF4 key Press to initiate a call. Keypad 0 ~ 9 Use the DTMF keypad to enter Selcall or Status number

The normalized values of these four analog levels are: +3, +1, –1 and –3. Each represents a symbol or quat. To provide precise adjustment of the transmitted power, the level of the DAC may be adjusted. The Transmitter Gain Register [tx_gain; 0x29] sets the level. During the manufacturing of the Bt8960, one source of variation in the transmitter levels is process variations. The Transmitter Calibration Register [tx_calibrate; 0x28] contains a read-only value which nulls this variation. The value

We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL TK-2202L: 16-channel VHF FM Transceiver TK-3202L: 16-channel UHF FM Transceiver NOTICES TO THE USER . Government law prohibits the operation of unlicensed radio transmitters

. The ambient temperature should be between 41°F and 104°F (5°C and 40°C) while charging is in progress. Charging outside this range may not fully charge the battery. . The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack. 8 INSTALLING/ REMOVING THE BATTERY PACK . Do not short the battery terminals or dispose of the battery by fire. . Never attempt to remove the casing from the battery pack. 1 Align the battery pa

We believe this easy-to-use transceiver will provide you with dependable and reliable communications. This KENWOOD transceiver is a precision device. Treat it with care, and you will enjoy years of reliable operation. FEATURES • Compact design with a sturdy, polycarbonate body and a spring- loaded belt hook. • Can be used with the supplied Ni-MH battery pack or 3 AA batteries. • 15 channels with 121 tone/code settings for each channel, allowing you to ignore unwanted calls. • Privacy Talk scramb

• If an abnormal odor or smoke is detected coming from the transceiver, immediately switch OFF the power and remove the batteries from the transceiver. Contact your KENWOOD dealer. . Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. . Illegal operation is punishable by fine and/or imprisonment. SAFETY: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. CONTENTS UN