Description Attachment 1695468 522E, 22" Single Stage Snow Thrower 1695514 522EX, 22" Single Stage Snow Thrower Not for Reproduction Rev. 11/2008 TP 400-5004-00-ST-S Part No.: 1737494 Not for Reproduction Table Of Contentss PRODUCT COMPONENTS PAGES Frame and Fuel Tank ........................................................................................................................................... 4 Engine Drive System .....................................................................

All rights reserved Decals NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Not for The above parts group applies to the following Mfg. Nos.: 1695468 - 522E 1695514 - 522EX Briggs and Stratton Yard Power Products Group Copyright © 2008 by Briggs and Stratton Corporation 14 TP 400-5004-00-ST-S Milwaukee, WI, USA. All rights reserved Decals REF NO PART NO. QTY. DESCRIPTION 1 1736343YP 1 DECAL, Control Panel Electric Start (Domestic Only) 1 1740400MA 1 DECAL, Cont

However, we reserve the right to change, alter or otherwise improve the product and this document at any time without prior notice. Read the Operator’s Manual • Locate the operator’s manual in the manual packet. Always read and follow the instructions in the operator’s manual. Proper care, performance tips, and safety information are located in this important document. • “Right” and “Left” are from the Operating Position. Raise The Handles • Cut four orange zip ties (E, Figure 3) that secure con

16 x 1" 4 720002 7 Lock Washer, 3/S" 5 717003 7 Hex Nut, Full 3/8"-16 6 107106 2 Shoe Assy. 7 719001 4 Flat Washer, 3/S” 8 720002 4 Lock Washer, 3/8" 9 705004 4 Hex. Cap Screw, 174054 S/8'J-16 x 3/4" 10 1 Pivot Frame Assy. 11 715100 2 Hex Capscrew, l/2”-13 x 1-1/2" 12 717518 2 Hex Nut, 1/2"* 13 13 107116 1 Pivot Plate Assy. 14 722006 2 Cotter Pin 1/8“ x 1" 15 107118 1 Pivot Rod 16 722001 2 Cotter Pin, 3/32” x 3/4" 17 107119 1 Pivot Arm id 156150 1 Spacer 19 705007 1 Hex Capsc

Place the pivot pin through the blade assembly bracket and push bar. Position the push bar under the tractor front axel and attach it to the axel using two pins and spring clips. Attach the spring end of the lift rod to the push bar assembly and the other end to the tractor lift arm using two spring clips. OPERATION Alternate holes are provided to permit adjustment of the shoe assemblies for raising or lowering the blade when cleaning gravel drives or walks. When cleaning concrete it is desira

Sound Power in Decibels J. Sound Pressure at Operator’s Position in Decibels K. Vibration This unit complies with ISO 8437, European Machinery Directive 98/37/EC, and European EMC Directive 89/336/EC. PRODUCT REFERENCE DATA Model Description Name/Number Unit MFG Number Unit SERIAL Number Mower Deck MFG Number Mower Deck SERIAL Number Dealer Name Date Purchased ENGINE REFERENCE DATA 1 Engine Make Engine Model Engine Type/Spec Engine Code/Serial Number Mfg. No.: 269XXXX Serial No.:

Press: • Body - 1 color, 2-sided • Cover - 1 color, 1 sided Bindery: • Saddle stitch, face trim *if too thick for saddle stitch, tape bind Covers: • FRONT COVER is present at the beginning of the file. • BACK COVER is the page immediately after the front cover. • The part number for this manual (typically a 172_____ number) is located on the front cover. • This file may contain several manual which differ only by their covers. See the part number at the bottom of the cover page. . Body: • The bo

• Slide the rubber dust cover (F) over the plastic fitting (B). 2 3 8 Figure 7 TP 1000-4518-01-LW-S Form No. 173xxxx-00 Two-Stage Snowthrower 1694986 10530L, 10.5 Snowthrower B A A C D B D Figure 3 A B C A B C D A B D E C D B A A B Remove Snowthrower From Crate • Cut the two zip ties from between wheels and the wood pallet. • Remove screws (A, Figure 11) from both skid shoes (B). • Roll snowthrower off crate. Add Oil and Fuel Note: Engine is NOT shipped with oil. Add 5W-30 premium engine oil. Se

Grease Tube Tire Sealant Degrimer/Degreaser Gas Stabilizer Additional copies of this manual are available, as well as fully illustrated parts lists. These manuals show all of the product’s components in exploded views (3D illustrations which show the relationship of parts and how they go together) as well as part numbers and quantities used. Important assembly notes and torque values are also included. For applicable manuals currently available for your model, contact our Customer Publication

All WARNING, CAUTION, and instructional messages on your unit should be carefully read and obeyed. Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important. The safety decals below are on your unit. If any of these decals are lost or damaged, replace them at once. See your local dealer for replacements. These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment,