ITEM Spark plug gap Valve clearance Other specifications MAINTENANCE Refer to page: 45 See your authorized Honda dealer 0.028 0.031 in (0.7 0.8 mm) IN: 0.15 0.02 mm EX: 0.20 0.02 mm (varies with snow conditions) (varies with snow conditions) Specifications are subject to change without notice. .. .. .. .. .. .. .. 71 TECHNICAL & CONSUMER INFORMATION Frame Engine Tuneup HS928 TA TAS WA WAS SZAS 28.5 in (725 mm) 40.9 in (1,038 mm) 41.0 in (1,042 mm) 231 lbs (105 kg) 240 lbs (109 kg) 28.0 in (710 m

To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. SPARK PLUG 1. Remove the spark plug cap. WRENCH 2. Clean any dirt from around the spark plug base. 3. Use the spark plug wrench supplied in the tool kit to remove the spark plug. 4. Inspect the spark plug. Replace it if the electrodes are worn or if the insulator is cracked, chipped, or fouled. .. .. ..

4.1 Set-Up Procedure — New Unit --------------------------------------------------------- 4.1 - 4.2 2 I-OPERATION & SERVICE INTRODUCTION: The information in section one is generally the same as that presented in the Snapper Operator's Manual. It is repeated here for general reference and adjustment purposes. RIGHT SIDE BLOWER CLUTCH HANDLE CONTROL PANEL FORWARD-REVERSE DIRECTIONAL CONTROL FUEL TANK FILLER CAP* (KEEP TIGHTENED) DISCHARGE DEFLECTOR CAP DISCHARGE CHUTE IMPELLER HOUSING

Description Attachment 1695468 522E, 22" Single Stage Snow Thrower 1695514 522EX, 22" Single Stage Snow Thrower Not for Reproduction Rev. 11/2008 TP 400-5004-00-ST-S Part No.: 1737494 Not for Reproduction Table Of Contentss PRODUCT COMPONENTS PAGES Frame and Fuel Tank ........................................................................................................................................... 4 Engine Drive System .....................................................................

All rights reserved Decals NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Not for The above parts group applies to the following Mfg. Nos.: 1695468 - 522E 1695514 - 522EX Briggs and Stratton Yard Power Products Group Copyright © 2008 by Briggs and Stratton Corporation 14 TP 400-5004-00-ST-S Milwaukee, WI, USA. All rights reserved Decals REF NO PART NO. QTY. DESCRIPTION 1 1736343YP 1 DECAL, Control Panel Electric Start (Domestic Only) 1 1740400MA 1 DECAL, Cont

This two-stage Thrower will do a great job of clearing snow from your drives and walks on the rear engine Rider which not only provides weight on the rear drive wheels for excellent traction but gives you good forward visibility. This manual covers the recommended procedures for operating the unit as a snow thrower plus detailed instructions for converting the Rider to and from the mower mode as the seasons change. Before operating in the snow thrower mode, be sure to read the important safety i

Refer to back page for kit information. CHARGING-ON UNIT. If the battery has insufficient energy to crank the engine for starting, rope start the engine and allow it to run at medium to fast speed to restore charge. CHARGING-AUTO TYPE CHARGER: If the battery charge cannot be restored by running the engine, it may be too deeply discharged to accept charge. In this event, disconnect and remove the battery from the unit and charge on an automotive type charger at LOW RATE only (2 amp maximum) for

However, we reserve the right to change, alter or otherwise improve the product and this document at any time without prior notice. Read the Operator’s Manual • Locate the operator’s manual in the manual packet. Always read and follow the instructions in the operator’s manual. Proper care, performance tips, and safety information are located in this important document. • “Right” and “Left” are from the Operating Position. Raise The Handles • Cut four orange zip ties (E, Figure 3) that secure con

CHECK OIL LEVEL OFTEN DURING ENGINE BREAK-IN. A. POSITION EQUIPMENT SO ENGINE IS LEVEL. B. Clean area around oil fill plug (see Figure 1). C. Remove oil fill plug and dipstick. D. Wipe dipstick clean, insert it into oil fill hole and tighten securely. Remove dipstick. If oil is not up to “FULL” mark on dipstick, add recommended oil. POUR SLOWLY. Wipe dipstick clean each time oil level is checked. IMPORTANT: DO NOT FILL ABOVE “FULL” MARK ON DIPSTICK. E. Install oil fill plug and dipstick, t

S. Environmental Protection Agency (“EPA”), the California Air Resources Board (“GARB”) and Tecumseh Products Co. are pleased to explain the Federal and California Emission Control Systems Warranty on your new smaii off-road engine. In California, new 1995 and later small off-road engines must be designed, built and equipped to meet the State’s stringent anti-smog standards. In other states, new 1997 and later model year engines must be designed, built and equipped, at the time of sale, to meet