Iniciar sesión:
Clasificado: Nombre ↓   Descargas   Tarifa   Tamaño ↑  
Descargado: 1   Tamaño del archivo: 1 mb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

Flush the pump, In–line Valve and pressure roller immediately after each use to prevent paint from drying in the pressure roller and damaging it. Cleanup page 17. 14 309388 Rolling Techniques 1. Rolling vertically, roll out the letter “M”. 2. Cross roll, horizontally, to spread the paint. 3. Finish with light vertical strokes until the entire area has been evenly covered. 309388 15 Ceilings, Woodwork and Walls 1. Ceilings: Using a paint brush, apply a starting row of paint approximately the widt

Descargado: 2   Tamaño del archivo: 594 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

7. Apply thread lubricant to the screws (15) and install them with the lockwashers (16) in the pump housing. Torque the screws a few inch–pounds (N.m) at a time, oppositely and evenly, to 85 in–lb (9.6 N.m). 8. Spin the motor shaft (D) to be sure it turns freely. 9. Reinstall the front cover (23). Priming Valve & Tube (See Fig 15.) NOTE: Each new priming valve kit includes a priming tube and fittings. 1. Unscrew the nut on the handle (E) of the priming valve (10a). Unscrew the stem of the handle

Descargado: 3   Tamaño del archivo: 281 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

Supersedes E READ AND RETAIN FOR REFERENCE. 50 Hz, 220/240 Volts, 0.5 Amp PT2000 Pressure Roller System 17.5bar (250 psi) MAXIMUM WORKING PRESSURE Model 220–240, Series E Complete System with hose, roller valve, extension and roller Model 221–076, Series E Basic System without hose, roller valve, extension or roller PATENT NO, 4,652,024 GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 1986, GRACO INC. TABLE OF CONTENTS Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Descargado: 0   Tamaño del archivo: 281 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

These fluids quickly destroy the hose material. Use the optional chemical–resistant hoses. See ACCESSORIES, page 17, for ordering optional hoses. 1. With the system fully primed, trigger the roller valve briefly until paint comes to the roller. 2. Experiment with triggering and rolling the paint until you determine just how often you need to trigger the roller valve to keep an even flow of paint to the roller. 3. To adjust the extension tube length, loosen the locknut and extend or retract the t

Descargado: 1   Tamaño del archivo: 594 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

Be sure they are in good condition and have undamaged three-pin plugs. Replace immediately if either cord shows signs of wear or damage. 3. Plug the power supply cord into a properly grounded, 120 V electrical outlet. See Fig 2. Do not use an adapter. All extension cords must have three wires. Use the chart below for selecting the appropriate wire gauge for the extension cord. . . PRIMING VALVE PAINT FILTER USE TWO WRENCHES TO TIGHTEN 25 FT. (7.6 M) HOSE BE SURE GASKETS ARE INSTALLED AT THESE JO

Descargado: 1   Tamaño del archivo: 81 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

READ AND KEEP FOR REFERENCE. INSTRUCTIONS Pressure Roller Model 243066, Series A . 20 in. (50 cm) heavy-duty extension . 45 swivel adapter . 9 in. (23 cm) roller frame . 1/2 in. (13 mm) nap roller cover 3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure * This maximum pressure is only possible if the roller frame is * completely plugged. The best operating pressure is the lowest pressure that provides an even paint supply to the roller and typically does not exceed 300 psi (2.1 MPa, 21 ba

Descargado: 1   Tamaño del archivo: 250 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

Now clear the needle or hose. Electric Switch Hand Held Valve . Be sure the air supply lines are connected correctly to the OPEN and CLOSE valve air ports. . To open or close the valve and maintain the open or closed status, a minimum of 40 psi (280 kPa, 2.8 bar) air pressure must be supplied and maintained at the OPEN or CLOSE port. . The trigger only activates the electrical switch in the handle, which turns the remote solenoid on and off. . Trigger the gun to turn the solenoid on. Release the

Descargado: 9   Tamaño del archivo: 250 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

308876K For dispensing a wide variety of single component sealants and adhesives. 4000 psi (28 MPa, 276 bar) Maximum Fluid Working Pressure 120 psi (0.84 MPa, 8.4 bar) Maximum Air Inlet Pressure See page 2 for Table of Contents Part No. 965766 Stainless Steel Wetted Parts, Machine Mount Valve Part No. 965767 Aluminum Wetted Parts, Hand–held Valve with internal air switch Part No. 965768 Aluminum Wetted Parts, Hand–held Valve with electric switch for remote operation Part No. 965786 Aluminum Wett

Descargado: 0   Tamaño del archivo: 313 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your distributor for information. • Route hoses and cables away from traffic areas, sharp edg

Descargado: 4   Tamaño del archivo: 129 kb   Fabricar: Graco Inc.  
Categoría: Otras herramientas
@name

See Cleaning on page 3. 2 309323 Cleaning This is the procedure for flushing the pressure roller. The pump and gun you are using may have additional flushing steps, such as cleaning filters and screens. See the pump and gun flushing instructions. NOTE: Leave the pressure roller attached to the gun for this procedure. See Pressure Relief Procedure on page 2. 1. Relieve the pressure. 2. Remove roller cover (19) and diffuser (23) from roller frame as follows (see Parts Drawing): a. Using your thumb





Categoría