WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. 1 2 3 4 5 6 7 SASSAFRAS SUPER SIZE LOG PLACEMENT EMBER PLACEMENT LS-18RSS-1 PHOTOS Do not cover any large rear ports withloose material (glowing embers) Photo 1 Photo2 Do not cover any large front ports withloose material (glowing embers) . Page 5 Photo3Photo4SomelogshavebeenremovedforclaritySomelogshavebeenremovedforclarity 20171-3-0907 EMBER PLACEMENT LS-24RSS-1 PHOTOS Some logs have been remov

GENERAL INFORMATION Qualified Installing Agency Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be performed only by a qualified agency. The term "qualified agency" means any individual, firm, corporation, or company that either in person or through a representative is engaged in and is responsible for(a)theinstallation,testing,or replacementofgaspipingor(b)the connection, installation, testing, repair, or servicing

WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number Log Placement LS-(18, 24, 30)RS Logs Figure 1 The following WARNING applies when log set is installed onto an unvented gas burner assembly. WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. LS-18RS 15999 LS-24RS 15970 LS-30RS 15970 Platinum Bright Embers PE-20-1 Note: Asingle layer of embers is to be used

Only non-combustible materials may be used to cover the black fireplace front. Warning: When finishing the fireplace never obstruct or modify the air inlet/outlet louvers in any manner. Provide adequate clearances around air openings into the combustion chamber. Caution: If the joints between the finished wall and the fireplace surround (top and sides) are sealed, a 300°F minimum sealant material must be used. These joints are not required to be sealed. Only non-combustible material (using 300°F

Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. 1. Stop! Read the safety information above. 2. Set the thermostat to lowest setting. 3. Turn off all electric power to the appliance. 4. This appliance is equipped with an ignition device which automatically l

Index Part No. Number Description BIRCH LOG SETS LS-18B2 1 R8331 Rear Log 2 R8329 Left Front Log 3 R8330 Right Front Log 4 R8332 Y Branch LS-24B2 1 R8335 Rear Log 2 R8333 Left Front Log 3 R8334 Right Front Log 4 R8336 Y Branch LS-30B2 1 R8288 Rear Log 2 R8337 Left Front Log 3 R8338 Right Front Log 4 R8339 Y Branch 1234 USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. HOW TO ORDER REPAIR PARTS Parts can be ordered only through your service person or d

Sooting and other problems may result if the logs are not properly and firmly positioned in the appliance. Refer to Figure 1 and Figure 1A for the following warning. Warning: Failure to position the parts in accordance with this diagram or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. PROPER INSTALLATION SEQUENCE: LS-(18,24,30)B2-1: (Figure 1) 1. Place rear (#1) log onto two (2) pins on rear log support. 2. Place left, front

Logs must be correctly positioned onto the burner. The photos in this manual show the proper pinned position for logs on this set. Owners need to be shown proper log placement and instructed not to move the logs. Logs must fit firmly onto the burner when positioned as shown in the photos. Malformed logs or logs with sloppy pin holes must be replaced. Proper Placement of Rock Wool and Decorative Lava Rock Rock wool can be added to burners for a glowing ember effect. It must be positioned only on

Replacement Loose Material (glowing embers) Part Number LS-18P 15999 LS-24P 15970 LS-30P 15970 Platinum Bright Embers PE-20-1 Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18, 24, 30)P Logs Figure 5 Attention: Do not use Figures 1 to 5 to order replacement logs. Refer to Page 11, Parts List and Parts View to order logs for your appropriate model number. The following WARNING appl

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer,