2. Remove filter end cover screws using 5/16" nut-driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut-driver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .076/.101 mm (.003"/.004") if needed (see Figure 25). Note: Rotate rotor one full turn to ensure the gap is .076/.101 mm (.003"/.004") at tightest

Board Support Strain Relief Bushing Power Cord Side Cover Screw/Lockwasher, 1/2" Nylon Locknut Wire Assembly (Brown) ON/OFF Switch Switch Cover Lockwasher, #10 Nut, #10-32 Edge Liner Wire Assembly (White) 2 1 1 1 1 1 1 1 1 1 1 1 6 8 1 1 1 5 1 1 1 4 1 1 1 1 1 3 1 1 PARTS AVAILABLE - NOT SHOWN HA2210 Filler Neck Screen 1 11 M50631 Rubber Bumper 2 103814-01 Wire Tie 1 12 101206-01 Motor Mounting Bracket 1 097650-01 Tradename Decal 2 13 101695-01 Button Plug 1 106013-03 Decal Package 1 14 104068-04

Models -Modeles -Modellen - Modelle: B35CEH, B70CEH, B100CEH, B150CEH 105398 R R PORTABLE FORCED AIR HEATERS OWNER’S MANUAL Heater Sizes: 35,000 70,000 100,000 150,000 Btu/Hr Models: B35CEH, B70CEH, B100CEH, and B150CEH IMPORTANT: Read and understand this manual before assembling, start- ing or servicing heater. Improper use of heater can cause serious injury. Keep this manual for future reference. R R PORTABLE FORCED AIR HEATERS SAFETY INFORMATION WARNINGS IMPORTANT: Read this owner’s manual ca

Severe burns and electrical shock can occur. HEATER WITH FUSED OR NON-FUSED IGNITION CONTROL ASSEMBLY FAULT CONDITION POSSIBLE CAUSE REMEDY Motor does not start five seconds after heater 1. Bad electrical connection between motor 1. Check all electrical connections. See is plugged in (ON/OFF switch light remains and ignition control assembly or ignition Wiring Diagram, page 23 on) control assembly and power cord WARNING: High voltage! 2. Binding pump rotor 2. If fan does not turn freely, see Pum

RADIANT PANEL SYSTEM® PLANNING & INSTALLATION MANUAL (rev) ROTH HEATING SYSTEMS 5A. INTRODUCTION The Roth Radiant Panel System® was developed for the wood frame houses of the North American and Scandinavian markets. It was designed for easy installation over any new or existing sub-floor, wood or concrete, and for use with many different floor coverings, such as carpet, tile or hardwood. This is done without the structural changes needed to accommodate the additional load of lightweight concrete

. CБОРКА .. Соблюдайте местные законы .. Поставьте нагреватель на ровном беттонном полу .. Установите распределитель и стальной провод на WА 29 А .. Устраните все орудие и части находящееся в камере сгорания .. Выравните нагреватель. Для проверки выравнения нагревателя установите тарелку сгорания (22) на дне камеры сгорания и налите немножко дизельного топлива, которое должно быть в середине тарелки. .. Всегда установите элемент в виде буквы т, включая стабилизатор тяги, на выпускной трубе каме

102D (For Home Use Only) Listed _ „ (£)„.. Air Compressor SPECIFICATION CHART Model No. 102D Horsepower 3/4 SCFM @ 40 psig 2.9 SCFM @ 90 psig 2.1 Displacement CFM 4.0 Bore 1 3/4" Stroke 1 1/4" Voltage-Single Phase 110-120 Minimum Branch Circuit Requirement 15 AMPS *Fuse Type Quick Acting Amperage at Max. Pressure 10 Tank Size 2 Gallon *A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same rating as the branch circuit the air compressor is operated

5. Si se esta almacenando la unidad, almacenarla en un lugar seco. Asegurarse que el lugar de almacenamiento este libre de polvo y vapores corrosivos. IMPORTANTE: No almacenar el keroseno durante el verano para usarlo en la siguiente temporada fria. El usar keroseno viejo podria danar el calentador. Item Tanque de combusti ble Filtros de salida de aire y de pelusa Filtro de admision de aire Filtro de combustible Bujia Paletas del ventilador Motor Intervalo Enjuaguelo cada 150-200 horas de funcio

2. Quite el ventilador (vea la pagina 13). 3. Quite las mangueras de las lineas de aire y de combustible del quemador. 4. Quite el cable de la bujia. 5. Quite la bujia del quemador con una llave de boca de 13/16". 6. Quite los tres tornillos con una llave de tuercas de 5/16" y quite el quemador de la camara de combustion. 7. Coloque el quemador en una prensa y apretarla ligeramente. 8. Quite cuidadosamente la boquilla del quemador usando una llave de casquillo de 5/8" (vea la Figura 24). 9. Sopl