This panel incorporates a thermostatic mixing valve. The high temperature limit stop on the mixing valve can be reset to comply with local plumbing codes. See page 10. *Know and follow all applicable local plumbing codes when setting the temperature on the water heater. Preparation for Installation Install 1/2” IPS nipples for the hot and cold water supplies at the locations shown on the diagram. The nipples should extend 5/8” outside the surface of the finish wall. For proper operation of the u

If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as Lime-Away™ or CLR™ ,into a shallow dish. Dilute the remover according to the label instructions. Soak only the spray face in the solution for the amount of time specified on the label. Install the handshower. Flush the handshower with clear water for at least one minute. Rinse the handshower with clear water. English 16 If the water pressure decreases as the water is made warmer, clean the car

water pressure Pression d’eau maximum 147 psi Recommended hot water temp. Temperature recommandee d'eau chaude 120.. - 140.. F* Max. hot water temp Temperature maximum d'eau chaude 158..F* Flow rate of handshower Debit de douchette 2.5 gpm Flow rate of each bodyspray Debit de chaque jet mural <1.0 gpm Flow rate of thermostatic mixing valve Debit maximum du mitigeur thermostatique 8 gpm @ 45 psi 10 gpm @ 65 psi *Please know and follow all applicable local plumbing codes when setting the temperatu

Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation. Inspect the ShowerArc thoroughly for shipping damage before beginning installation. The installation shown on page 2 is ideal for users of approx. 5’11” in height The installation height may be increased, if desired. All measurements, including the minimum ceiling height, must be increased as well. The ShowerArc requires 1/2” NPT female

Make sure that you have all tools and supplies needed to complete the installation. Technical Information Recommended water pressure 14.7 - 72.5 psi Max. water pressure 147 psi Recommended hot water temp. 120.. - 140.. F* Max. hot water temp 165..F* Hole size in mounting surface 1 1/4” valves, 1 3/8” spout Max. mounting surface depth 1 1/2” Flow rate 2.2 gpm Requires 1/2” supply lines (not included) *Please know and follow all applicable local plumbing codes when setting the temperature on the w

When satisfied with the action of the drain, slide the other end of the spring clip over the end of the horizontal rod. plunger height adjuster flange sealing gasket link mack gasket spring clip friction ring retainer nut nut horizontal rod pivot ball pivot ball seals pivot tee tailpiece Robinets de lavabo Limbo C Tango C Swing C Solaris E Stratos E Metro E A prendre en consideration pour l’installation Pour de meilleurs resultats, Hansgrohe recommande que ce produit soit installe par un plombie

rear cover To check the product suitability for commercial and multiple installations, please contact Triton's specification advisory service before installation. Telephone: 0870 067 3767 Facsimile: 0870 067 3334 E mail: technical@tritonshowers.co.uk Combi HP thermostatic mixer shower INTRODUCTION This book contains all the necessary fitting and operating instructions for your Triton high pressure thermostatic mixer shower. Please read them carefully. Please read through the whole of thi

120.. - 140.. F* Max. hot water temp 165..F* Max. flow rate: showerhead 2.5 gpm handshower 2.5 gpm neck spray 2.5 gpm bodysprays 0.72 gpm each Thermostatic temperature control The high temperature limit stop on the thermostatic mxing valve may be reset to comply with local plumbing codes. Protection against back siphonage provided by check valves. The check valves should be removed and inspected yearly. This panel may be used with an instantaneous water heater if the heater is at least 24 kW and

THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no- rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. (3)

2. A description of the problem. 3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492 Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe. When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid. EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PR