2009 - REV. 0 Printed in U.S.A. DistributedBy: Ordering Information “The Stinger has earned the trusted ARI Performance Certified™ seal, an assurance of the product’s performance in accordance with ARI Standard 740.” The new Stinger™ comes equipped with the new vacuum shut off allowing for unattended recovery operation, an easy-to-read low vacuum/tank full LED, carrying strap, and improved packaging to protect knobs and gauges. Providing you with new safety and reliability, the upgraded Stinger™

When operating this equipment, use good judgment work. and safety precautions to avoid damage to equipment and AVOID SPILLING liquid refrigerant on skin or getting it into the eyes. property or injury to personnel. USE SAFETY GOGGLES. Wash any spills from the skin with soap and Be sure you understand and follow the procedures and water. If liquid refrigerant enters the eyes, IMMEDIATELY FLUSH EYESsafety precautions contained in the chiller instructions as with water and consult a physician. well

. . . . . . . . . . . . . . . . . . . . 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-78 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Step 1 — Inspect Shipment . . . . . . . . . . . . . . . . . . . . . . 1 Step 2 — Place, Mount and Rig Unit. . . . . . . . . . . . .2 •PLACING UNIT • MOUNTING UNIT • RIGGING UNIT Step 3 — Cooler Fluid

NOTE: If DIP switch is set for Stage 2, the alarm relay will not cycle during Test mode. Heating/Cooling Thermostat Type — Switch 3 provides selection of thermostat type. Heat pump or heat/cool thermostatscan be selected. Select OFF for heat/cool thermostats. When inheat/cool mode, Y1 is used for Cooling Stage 1, Y2 is used forCooling Stage 2, W1 is used for Heating Stage 1 and O/W2 isused for Heating Stage 2. Select ON for heat pump applications. In heat pump mode, Y1 used is for Compressor Sta

SAT 1 J8 – 1,2 (SGC) Supply Air Thermistor (SAT) — Inserted into supply section underneath the gas heat section (factory-provided, field-installed) HH79NZ016 SAT 2 J8 – 3,4 (SGC) Supply Air Thermistor (SAT) — Inserted into supply section underneath the gas heat section (factory-provided, field-installed) SAT 3 J8 – 5,6 (SGC) Supply Air Thermistor (SAT) — Inserted into supply section underneath the gas heat section (factory-provided, field-installed) 30 Fig. 24 — Supply-Air Thermistor Connections

Check convenience outlet for power status before opening unit for service. Locate its disconnect switch, if appropriate, and open it. Lock- -- out and tag- -- out this switch, if necessary. 20 21 Two types of convenience outlets are offered on 48HC models: Non--unit powered and unit--powered. Both types provide a 125--volt GFCI (ground--fault circuit--interrupter) duplex receptacle rated at 15--A behind a hinged access cover, located on the corner panel of the unit. See Fig. 26. Convenience Outl

6. Alinee la ranura en V de cada soporte ensamblado sobre estas marcas y monte los soportes al umbral con los tornillos de 3/4" proporcionados. Los soportes deber n quedar perpendiculares al umbral interno de la ventana. Vea la (Fig. 6). C. Para permitir una descarga adecuada de la c ondensaci n, ser necesario ajustar la inclinaci n de los soportes en la ventana. Para ello, ajuste la distancia del tornillo de nivelaci n en la pared exterior. La inclinaci n m xima no deber ser superior a 3/16". V

Por lo tanto la unidad deber instalarse en un lugar donde la descarga de la condensaci n no gotee sobre el paso de peatones ni en las propiedades vecinas. PRECAUCI N ! ! Debido a que el compresor se encuentra del lado de los controles (a la derecha de la unidad), este lado ser m s pesado y m s dif cil de manipular. Si la unidad no se sostiene bien de dicho lado pueden producirse lesiones f sicas y danos a la unidad y a su propiedad. Por lo tanto, le recomendamos que para instalar esta unidad sol

Dicho r tulo se encuentra en el lado derecho de la unidad. Especificaciones el ctricas 1. Todos los cables deben cumplir con los c digos el ctricos locales y nacionales y los debe instalar un electricista licenciado. Si tiene preguntas relacionadas con las siguientes instrucciones, comun quese con un electricista licenciado. 2. Verifique el suministro de energ a disponible y resuelva cualquier problema con los cables ANTES de instalar y hacer funcionar esta unidad. 3. Para su seguridad y protecc