Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  

Lifebreath 94-EXCHANGER-MD

Descargado: 3Tamaño del archivo: 5 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

Due to the broad range of installation and operational conditions, consideration must be given for the possibility of condensation forming on the unit or connecting ducting. Objects below the installation may be exposed to condensate. • At least 3' (1 m) away from the corner of the building* • At least 3’ away from gas meter, electric meter or a walkway where fog or ice could create a hazard* • Not into a garage, workshop or other unheated space When installing the weather hood, its outside peri

Lifebreath 99-MD-KIT

Descargado: 6Tamaño del archivo: 5 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

Remove and wash filters and core and replace. Outside hoods should be visually checked for blockage regularly. 5. Drain is required as shown above. 6. Built in balancing damper may require seasonal adjustments. 8 Air Flow Balancing Air Flow Balancing It is necessary to have balanced air flow in an HRV. The volume of air brought in from the outside must equal the volume of air exhausted by the unit. If the air flow is not properly balanced, then: • The HRV may not operate at its maximum efficienc

Lifebreath 94-EXCHANGER

Descargado: 4Tamaño del archivo: 5 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

foil duct tape • knife • zip ties • caulking gun • 1/2” I.D. drain hose • smoke pencil Balancing Tools • Pitot Tube Balancing Kit [Case, 8 ft. vinyl tubing, Pitot tube, magnehelic gauge (0 -0.25”), and mounting plate] • Pitot Tube with instructions and Digital Manometer (with resolution of 0 -0.25” -must read to 1/100ths of an inch) ATTENTION See page 3 for 99-MD-KIT installation instructions Application Heat Recovery Ventilators (HRV) are designed to provide fresh air while exhausting an equal

Lifebreath Clean Air Furnace CAF-02-MB

Descargado: 2Tamaño del archivo: 4 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

Gas Furnaces, Oil Furnaces, Wood Stoves, etc.). NEVER install an HRV/ERV in a situation where its normal operation, lack of operation or partial failure may result in the backdrafting or improper functioning of vented combustion equipment!!! TO BE COMPLETED BY CONTRACTOR AFTER INSTALLATION Installing Contractor Telephone / Contact Serial Number Installation Date Model * LEAVE FOR HOMEOWNER NOTE: Due to ongoing research and product development, specifications, ratings and dimensions are subject t

Lifebreath 100 DEF

Descargado: 22Tamaño del archivo: 2 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

During the winter months, the incoming cold fresh air is warmed by utilizing the heat recovered from the stale air before it is exhausted to the outdoors. During the summer months, the cool outgoing stale air from the air conditioned dwelling is used to help cool the incoming fresh air. Your HRV features the digital electronic BASE MODULE that uses a microprocessor to control fan speed and unit operation. Both digital (3 wire) and standard (2 wire) remote devices can control the HRV when conne

Lifebreath 100 FN

Descargado: 5Tamaño del archivo: 2 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

The drain line must be located in an area that is not subject to freezing and should beoutletted into floor drain sink, standpipe or condensate pump. Make sure the drain line slopes down to provide proper condensate removal. Should no "fall" be available, a condensate pump may be used. NOTE: A P-Trap must be made to prevent odours from being drawn in through the drain line. THE DUCTWORK SYSTEM A well designed ducting system will allow the HRV to operate at its maximum efficiency. Air flow wi

Lifebreath RNC5-TPD

Descargado: 0Tamaño del archivo: 2 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

EXHAUST AIR from various parts of home. i.e. bathrooms (if required), kitchens (if required). Cool Air Return NOTES: 1. Furnace blower is recommended to operate when HRV is on to provide good air distribution. 2. Weatherhood arrangement is for drawing purposes only. 6' (2 m) minimum separation required. 18" (460 mm) above grade minimum. 3. Due to the differences in pressure between the HRV and the equipment it is being connected to, the HRV's airflow must be confirmed on site, using the balancin

Lifebreath RNC20

Descargado: 4Tamaño del archivo: 2 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

ALL DUCT COLLARS ARE 5” (127 mm) DIAMETER Option2-Vertical Duct Configuration Dimensions inches The HRV can be installed horizontally or vertically as illustrated Sufficient clearance below the access door is required for on the following pages. The unit should be suspended using the servicing the air filters and core. A minimum of 25" (635mm) provided hanging straps. The unit must be level for proper clearance is recommended so the door can be removed. Four condensate drainage. PVC reinforced p

Lifebreath RNC200

Descargado: 4Tamaño del archivo: 2 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

Changing OFF to STANDBY Figure 1 -Factory DIP Switch Settings The factory setting of the DIP switches (located on the circuit board) provides continuous low speed ventilation. Optional Remote Controls will initiate high speed ventilation. Remote controls with an ON/OFF switch (refer to "Remote Control Devices" in this manual) will shut the entire system down when the remote control is in the OFF position. Changing the remote control from OFF to STANDBY can be achieved by Setting the DIP Switch a

Lifebreath RNC95

Descargado: 1Tamaño del archivo: 2 mb    Fabricar: Lifebreath  
Categoría: Los aficionados

Step 6 Connect tubes to door ports as illustrated in Step 6. (record readings). Fresh Air Stale Air Step 5 Step 6 Measuring Fresh Air Side (Always connect left side port Measuring Stale Air Side (Always connect left side port first). first). 10203040706070809010001020304070607080901000 Note: It is normal practice to lightly tap gauge if reading is non-responsive. Step 7 Damper airflows as required. Step 8 Repeat Steps 5 and 6 as required to confirm airflows 26 Air Flow Balancing using the Door P





Categoría