Refer to back page for kit information. CHARGING-ON UNIT. If the battery has insufficient energy to crank the engine for starting, rope start the engine and allow it to run at medium to fast speed to restore charge. CHARGING-AUTO TYPE CHARGER: If the battery charge cannot be restored by running the engine, it may be too deeply discharged to accept charge. In this event, disconnect and remove the battery from the unit and charge on an automotive type charger at LOW RATE only (2 amp maximum) for

ALL RIGHTS RESERVED MANUAL No. 7-3571 (Rev. 1, 7/28/00) IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects thatcan cause injury and damage! Failure to comply with the following SAFETY instructions could result in seriousinjury or death to the operator or other persons. The owner of the machine must understand these instructionsand must allow only persons who understand these instructions to operate machine. Each pers

Depress belt idler and remove the inside (forward) clutch drive belt. See Figure 1.1. REMOVE INSIDE CLUTCH DRIVE BELT WIRING ELECTRIC CLUTCH HARNESS CONNECTOR CONNECTOR FIGURE 1.1 IMPORTANT: The grass catcher kit includes two different length blower drive belts. Carefully check thepart numbers to insure you install the correct belt onyour machine. 1) Belt Part No. 7-2738 fits ZMT and machines with the # 6-3165 Drive Shaft Lowering Kit installed. 2) Belt Part No. 4-6249 fits all other Mid-Mount m

1, 1/24/03) MANUAL No. 06613 CONTENTS LAWN TRACTOR MODEL IDENTIFICATION Positive identification of the machine will be necessary. Identify the machine with the model number to insure the correct kit is used for that model. The series number or letter of the model number is used in this manual to match the correct kit with the correct model. Refer to Owner’s Manual for correct Series number. The series number for all disc, gear and hydro drive two piece frame models is 0, 1, 2. The series number

This two-stage Thrower will do a great job of clearing snow from your drives and walks on the rear engine Rider which not only provides weight on the rear drive wheels for excellent traction but gives you good forward visibility. This manual covers the recommended procedures for operating the unit as a snow thrower plus detailed instructions for converting the Rider to and from the mower mode as the seasons change. Before operating in the snow thrower mode, be sure to read the important safety i

The Grass Catcher is optional equipment on some models. 11 18 22 :\ 25 27 _25 24 24 BLOP_ERUNIT GROUP 25 25 CZT / HZT Models 28 26 * Grease Fitting Orientation 12 SntlllllKl-l/tlc lloilr llnl! SrOUll-CJT/ETmedel$ Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 26 27 28 29 3O Part No. 3046782 91121 90183 3021097 44995 91804 14409 10776 3046824 91527 3047253 91601 91218 3046781 3046853 91541 3022832 90839 3031920 3046854 3031919 90613 3046813 3043613 90122 91560 91518 91305

Tighten securely. BAGGER KIT INSTALLATION STEP 11: Install bumper mount standoffs onto rear bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out. NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List section of the manual. STEP 12: Install bumper

NO. 1691277 Table of Contents Accessories............................................... Inside Front Cover Safety Rules . ........................................................... 1 Decals...................................................................2 Parts Identification............................W................2 Layout of Assembly Parts . ...............................................3 Installation and Removal.......................... ..............................4 Instal

Lea el manual del operador para obtener información completa de seguridad, instalación, operación, mantenimiento y reparación. SIMBOLO A © © I«M—• SIGNIFICADO • SÍMBOLO DE ALERTA DE SEGURIDAD Indica peligro, advertencia o precaución. , Puede ser usado junto con otros símbolos o pictografías. • ADVERTENCIA - LEA EL MANUAL DEL OPERADOR Lea el (los) manual(es) del operador y siga todas las instrucciones de advertencias y seguridad. Dejar de hacerlo puede ocasionar lesiones graves al oper

Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! COPYRIGHT © 2001 SNAPPER INC. ALL RIGHTS RESERVED MANUAL No. 7-4270 (I.R. 11/31/01) IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that cancause injury and damage! Failure to comply with the following instructions may result in serious in