Disyuntor termico de seguridad La estufa incorpora un disyuntor termico de seguridad, para evitar danos por recalentamiento. Esto puede ocurrir si la salida de calor o el tiro de la chimenea estaban obstruidos de algun modo. Si el disyuntor se activa, desenchufe la estufa de la toma de corriente y deje pasar al menos 10 minutos antes de volver a enchufarlo. Antes de volver a conectar la estufa, retire la obstruccion de la salida de calor y reanude el funcionamiento del equipo. Sugerencias para e

La utilizacion del efecto de llama apenas consume electricidad. Estos modelos estan disenados para colocarlos de pie, generalmente cerca de una pared. Antes de conectar la estufa, compruebe que la tension de alimentacion coincida con la del aparato. Tenga en cuenta que: si utiliza el aparato en un lugar muy silencioso, es posible que escuche un ruido debido al efecto llama. Esto es normal y no debe constituir motivo de preocupacion. Conexion electrica. ADVERTENCIA: ESTE APARATO DEBE CONECTARSE A

11. Limpie la superficie de salida de la tapa del sumidero con el cepillo y aclare con un chorro de agua. (Consulte las Fig. 15 y 16) 12. Siga los pasos anteriores en sentido inverso para volver a montar el conjunto. Filtro de aire. 1. Ponga el interruptor “A” en la posicion “OFF” (0) (consulte la Fig. 2) 2. Tire suavemente del cajon hasta el tope. (Consulte la Fig. 3) 3. Retire el deposito y coloquelo en el fregadero con la tapa hacia arriba. 4. Deslice suavemente hacia arriba el soporte de pla

Alternative condensate discharge options have to be agreed with the manufacturer. Do not discharge the condensate directly into septic pits or cesspools as the evaporator is likely to be destroyed by the aggressive vapours generated there. 5 MOUNTING 6 6 MOUNTING 6.1 General The following connections need to be established on the heat pump: -supply/return lines of the heating system -condensate drain -control lead to the remote control -power supply 6.2 Heating-Side Connection The connections on

The heating mode can be preselected by placing switch (3) to the Heating ( ) position. The desired return temperature can be set using selector dial (4), the relevant call for heat is controlled by the potentiometer and lies within a range of min. 10 °C and max. 55 °C. If the preset temperature is reached, the heat pump switches off. Once the return temperature drops below the preset temperature by 4 Kelvin, the heat pump switches back on. In the event that the preset return temperature cannot b

power input to pump) Air inlet temperature in [°C] Coefficient of performance (incl. power input to pump) Air inlet temperature in [°C] Condenser Heating water flow rate in [m3/h] 0 0,5 1 1,5 2 2,5 3 20 APPENDIX: 12.3 SCHEMATICS 12.3.8 Cooling mode LA 12TR 0 5 10 15 20 25 30 10 15 20 25 30 35 40 45 50 18 8 0 1 2 3 4 5 6 7 10 15 20 25 30 35 40 45 50 18 8 0 1 2 3 4 5 6 7 10 15 20 25 30 35 40 45 50 18 8 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 Cooling capacity in [kW] Conditions: Water f

In this context, particular attention must be paid to the proper disposal of refrigerants and refrigeration oils. 10 APPENDIX 12 12 APPENDIX 12.1 DIMENSIONED DRAWING 12 12.2 EQUIPMENT DATA 13 12.3 SCHEMATICS 12.3.1 Heating mode LA 6MR 14 12.3.2 Cooling mode LA 6MR 15 12.3.3 Heating mode LA 8MR 16 12.3.4 Cooling mode LA 8MR 17 12.3.5 Heating mode LA 10MR 18 12.3.6 Cooling mode LA 10MR 19 12.3.7 Heating mode LA 12TR 20 12.3.8 Cooling mode LA 12TR 21 12.3.9 Heating mode LA 16TR 22 12.3.10 Cooling m

CAUTION! CAUTION! damage the surface. CAUTION! CAUTION! CAUTION! Do not open the unit unless all electrical circuits have been disconnected from the During transport, the heat pump must not be tilted more than 45° (in either direction). Heat pump and transport pallet are only connected by the packaging film. The air intake and discharge openings must neither be constricted nor Clockwise phase sequence (in the case of multiphase units) must be observed: Damage to the compressor may be incurred if

We trust this manual will give you all the answers to the questions that you might have regarding the products. Although every care was taken to ensure the content of this manual is correct we do not accept any liability for claims resulting directly or indirectly from the application of the information contained in this manual. This manual is written specifically for the Dimples Solar product range. Any information contained therein must not be applied generally to any other solar products. Sho