Improper oscillation. To check the sanding belt oscillation: 1. Be sure the sanding belt is properly installed and the belt tension knob and air supply are ON. 2. Turn ON the sanding belt. —If the belt oscillates without contacting the limit switches, but the oscillation time to the left and right are NOT equal, proceed to Step 7, on Page 31. 3. An adequate stream of air through the air fork gap (Figure 26) is essential for proper oscillation. If the jet of air is weak through the gap, the

#TS9703 PRINTED IN CHINA ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

this may pull the operator’s hand into the machine and cause serious injury! fEEDiNg STOcK. Firmly grasp the workpiece in both hands and ease it into the machine against the direction of rotation using light pressure. do not jam the workpiece into the machine during operation. never sand more than one piece of stock at a time. 6. 7. 8. REpLAciNg SANDiNg BELT. replace sanding belt when it becomes worn. a worn sanding belt can break apart during use, causing personal injury or damage to the machin

#JK7691 PRINTED IN CHINA Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or to order new labels. Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readabi

Accesorios, herramientas .Por razones de seguridad,solamente deben emplearse accesorios yherramientas originales de Festool. Los numeros de pedido para los respectivosaccesorios y herramientas se encuentran en sucatalogo Festool. Garanti. Condiciones de la Garantia 1 + 2 Usted tiene derecho a una garantia extendidagratuita (1 ano + 2 anos = 3 anos) para suherramienta mecanica Festool. Festool se hararesponsable por los costos de envio durante elprimer ano de garantia. Durante el segundo ytercer

En caso de danos, arregle laherramienta antes de usarla. Muchosaccidentes son causados por herramientas conmal mantenimiento. 17 Use solo accesorios que recomiende elfabricante para su modelo. Accesorios quefuncionen en una herramienta pueden serpeligrosos al usarlos en otra. Mantenimiento18 El mantenimiento de la herramientasolo se podra realizar por personal demantenimiento calificado. Revision omantenimiento realizado por personal nocalificado puede resultar en el riesgo de lesion 19 Cuando s

Este sistema combina tres funciones enuna sola manguera. 14 -- ESxutmrainccisiotrno ddee aaiirree dceo mespcraimpeid (o1 .(21).1) - Extraccion de polvo (1.3) Conexion y desconexion . ver figura 2. iSnidsitceamciao ndees acdojnuenxtaio.n IAS 2 . ver hoja de Puesta en marcha Laal ehjeerrrcaemr ipenretasi onne uemna ltaic ap aslea npcoan e( 3e.n1 )m. aSric hsae suelta la palanca, la maquina se apaga. Ajustes de la maquina trabajo en la mAnatqeus idnea ,r eaelisztaar cudaelqbueirear cdoemscpornimeci

1. Low voltage. 2. Open circuit in motor or loose connections. 1. Check power line for proper voltage. 2. Inspect all lead connections on motor for loose or open connections. Motor will not start; fuses or circuit breakers blow. 1. Short circuit in line cord or plug. 2. Short circuit in motor or loose connections. 3. Incorrect fuses or circuit breakers in power line. 1. Inspect cord or plug for damaged insulation and shorted wires. 2. Inspect all connections on motor for loose or shorted termina