English 7 Day Programmable INSTALLATION5 MINUTE M T W T F S S Owner’s Manual Model 44905 Form# 44050-01 20100603 ©2010 Hunter Fan Co. English 7 Day Programmable INSTALLATION5 MINUTE M T W T F S S Table Of Contents At A Glance Know Your Thermostat 3 Setup Setting Day, Time, and System 8 Scheduling Scheduling Introduction 10 Setting Your Schedule 12 Temporary Temperature Change 18 Turning Off Scheduling 20 Home Today 22 Save Away 24 Features Alerts 26 Menu Options 30 Advanced Menu Options 34 Energ

Do not connect a cable to the Loop BNC unless it is connected to another terminated device because it will cause poor quality video. Connecting Audio Note It is your responsibility to determine if local laws and regulations permit recording audio. Figure 2-4 Audio In and Out Connectors AUDIO IN 1 AUDIO IN 2 AUDIO IN 3 AUDIO IN 4 AUDIO OUT Your DVR can record audio. 1. Connect the audio source to Audio In. 2. Connect Audio Out to your amplifier. Note The DVR does not have amplified audio output,

Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA 72 after any programming operation or change in site-s

Password: admin. (administrator, local and network) • Username: 888888. Password: 888888. (administrator, local only) • Username: 666666. Password: 666666(Lower authority user who can only monitor, playback, backup and etc.) • Username: default. Password: default(hidden user) You can use the USB mouse, front panel, remote controller or keyboard to input. About input method: Click or press Shift on the front panel to switch between numbers, English character (small/capitalized) and denotation. No

Overlay mode: There are two options: preview and encode. Preview means overlay the card number in the local monitor video. Encode means overlay the card number in the record file. Overlay Position: Here you can select the proper overlay position from the dropdown list. Figure 5-32 Text Overlay(COM Type) Network Type The network type interface is shown in Figure 5-33. Here we take the ATM/POS protocol to continue. There are two types: with or without the protocol according to client’s requirement

• In General interface please input upload interval. • In Detect interface please enable snapshot function for specified channels. Or in alarm interface please enable snapshot function for specified channels. Please refer to the following figure for detailed information. Figure 4-14 Activation Snapshot Setting Priority Please note the activation snapshot has the higher priority than schedule snapshot. If you have enabled these two types at the same time, system can activate the activation snapsh

Mating wet components may cause damage not covered by the warranty. 10 - 5 Charging a Spare Battery The base can also charge a second battery while the terminal is positioned in the base. The second battery can be inserted in the battery charging well in back of the terminal connection. Place the battery in the well with the label facing up and toward the back of the unit. Angle the battery as shown. Once the connectors engage, the LED lights. If the LED is red, the unit is charging; if it is gr

2 On-Screen Compass Allows On-Screen control of a PTZ camera. 3 RS-232 / RS-485 Defines how to send the PTZ signal to the camera. 4 Select Camera Selects the current camera to be edited. 5 Port Settings Defines the specific settings to transmit to the PTZ. 6 Enable Pan/Tilt Enables the DVR to control the PTZ camera. 7 Preset and Tour Used to create Presets and Tours for the PTZ camera. Since each camera creates these in a different way, there can be multiple methods. 8 Protocol Selects the proto

Funcionamiento nocturno En condiciones de buena luz de dia, el receptor muestra una imagen a color. Cuando exista poca iluminacion o en la noche la pantalla automaticamente cambia a blanco y negro. Los LED infrarrojos iluminan al visitante, de modo que puedan verse en el receptor incluso cuando estan rodeados de una oscuridad total. Indicacion de bateria baja de la camara Cuando las baterias de la camara de la puerta estan con poca carga, el receptor lo indica con un tono doble de advertencia qu

30 SEGUNDOSDESPUES DE QUE SE HAYAPRESIONADO EL BOTONBRILLO DELA PANTALLAVISIOCAMVOLUMEN DEL MIC– PARA USO FUTUROBOTON DE SELECCIONDE LA MELODIA– PARA LASEGUNDACAMARA/PULSADORINDICADOR DE BATERIALUZ INTERMITENTEDE LA CAMPANILLA Configuracion de la pre-instalacion Antes de fijar la camara de la puerta en su lugar, prepare y pruebe el sistema como sigue: Instale las baterias en la camara de la puerta Nota: La camara de la puerta tiene un interruptor integrado a prueba de manipulacion para ayudar a