This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800446- 5158) to obtain a Free copy before operating the equipment. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 210-372-3551 © 2008 Alamo Group Inc

7 After the first 50 hours of operation, change the oil and oil filter. + 2 1 + 4 DIESEL API CD-MIL L 2104D, CD/SE, CD/SF 3 S-177 571 0 . 50 h Std. 0 . 200A200A 5 50 h Std. Notes MATERIAL THICKNESS REFERENCE CHART 24 Gauge (.025 in) 22 Gauge (.031 in) 20 Gauge (.037 in) 18 Gauge (.050 in) 16 Gauge (.063 in) 14 Gauge (.078 in) 1/8 in (.125 in) 3/16 in (.188 in) 1/4 in (.25 in) 5/16 in (.313 in) 3/8 in (.375 in) OM-4428 Page 12 OM-4428 Page 13 3-2. Manufacturer’s Rating Labels CC Models CC/CV Mode

. . . . . . . . . . . . . . . . . . . . 2 ... 6 . . . . . . . . . . . . . 081499 . . BRACKET, mtg strip terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 7 . . . . . . . . . . . . . 206352 . . BRACE, front to center upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . 203260 . . LABEL, caution do not use ether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 8 . . SR

250 A 250 A, 25 V, 100% Duty Cycle 72 275 A, 25 V, CV/DC 17 . 28 V 60% Duty Cycle 250 A, 28 V, 41 100% Duty Cycle OM-217 455 Page 12 A complete Parts List is available at OM-217 455 Page 13 4-2. Dimensions, Weights, and Operating Angles Dimensions Height 35-1/2 in (902 mm) (To Top Of Exhaust) A B Width 20 in (508 mm) C ! D d il l i ld Depth 53 in (1346 mm) D Do not exceed tilt angles or engine could be damaged or unit could tip. A 20 in (508 mm) 4 H l G ! Do not move or operate unit where it co

Almacene los discos sobre una superficie plana y en un lugar seco, preferiblemente a una temperatura constante, en donde no exista el riesgo de congelacion. No almacene la sierra con un disco montado. Almacene la sierra en un lugar elevado o bajo llave, fuera del alcance de los ninos. Vacie el tanque de combustible antes de guardar la maquina por un lapso de mas de unos cuantos dias. Guarde el combustible unicamente en envases debidamente rotulados y aprobados para ello. Evite el contacto direct

injury or equipment damage can . Do not touch live electrical parts. ~fl S Keep away from moving parts. happen. )~ . Disconnect input power before S Keep all panels and covers closed 3 Statement Of Hazard And installing or servicing. wtten operating. Result -~_________ / 4 Safety Instructions To Avoid 5 Hazard 5 Hazard Symbol (If Available) 6 Safety Banner READSAFETYBLOCKSat start of Read safety blocks for each sym a WARNIF~ I 6 SectIon 3-1 berore proceeding. bol shown. 7 NOTE 7-HNOTED~ TurnOffs

Installing Weld Curtain £k 1 Weld Curtain Frame 2 Turntable Top 3 Capscrews 4 Weld Curtain 5 Support Bars I nstall weld curtain frame on turntable top with four capscrews. Position weld curtain in curtain frame and install support bar through frame and curtain. 3-8. Installing Input/Output Cable To Robot Use receptacle to connect input/ output cable to robot. 1 Receptacle RC1 2 Keyway 3 Plug 4 Threaded Connector To connect input/output cable to robot, align keyway, insert plug, and

Duty Cycle And Overheating........................................................................................................................9 3-3. Volt-Ampere Curves......................................................................................................................................9 3-4. Installing Gas Supply....................................................................................................................................10 3-5. Installing Wire Spool an

And if for some reason the unit needs repair, there’s a Troubleshooting section that will help you figure out what the problem is. The parts list will then help you to decide which exact part you may need to fix the problem. Warranty and service information for your particular model are also provided. Working as hard as you do - every power source from Miller is backed by the most hassle-free warranty in the business. Miller Electric manufactures a full line of welders and welding related equ

Routine Maintenance ik ± Disconnect power before maintaining. ^ Maintain more often during severe conditions. 3 Months Replace unreadable labels WARNlrt Ji — J»w Repair or replace cracked weld cable Clean and tighten weld terminals 6 Months Blow out or vacuum inside. Remove drive roll and carrier. Apply light coat of oil or grease to drive motor shaft. 5-2. Circuit Breaker CB1 ik > 1 Circuit Breaker CB1 CB1 protects the unit from overloading of drive motor M1. If