• Enfrie la plancha y almacenela segun las instrucciones. NOTA: No vierta agua dentro del orificio de la valvula de Vapor. Espanol-7 RECOMENDACIONES PARA EL PLANCHADO • Siempre lea las • Clasifique las prendas • Primero debe planchar las prendas (por ejemplo, las prendas de seda y tela sintetica) a fin de evitar danarlas con una demasiado caliente. • Si no esta seguro de cual es el contenido un area pequena, como por ejemplo una costura visible. Empiece con una temperatura baja y aumentela la te
Place steam wand into milk, approx. 1cm below surface and activate the steam function. Angle jug to rest steam wand on spout and place nozzle just below surface of the milk. Raise the jug until nozzle is in the centre of milk. Close the steam by turning dial anti-clockwise. Wipe steam nozzle and wand with damp cloth. Place cup under hot water nozzle and activate the hot water function. Close the hot water by turning dial clockwise. Swing hot water wand over the drip tray. 37 39 40 38 41 42 43 44
Release the ‘CLEAN’ and ‘DESCALE’ buttons and the Cafe Barista™ is now reset. Grind setting selection and maintenance (continued) Figure 43 Figure 42 Figure 44 Resetting the Cafe Barista™ 27 Care and cleaning Note: When the espresso machine is turned on it will go through an Auto Clean cycle. This removes any old coffee grinds from the coffee brewing unit. The coffee making process involves extracting oils out of coffee grinds to make espresso coffee. Deposits of these oils build up over time an
NBC1401 This grill is NOT a Weber® grill and is NOT in any way associated For Outdoor Use Only (outside any enclosure) Solamente Para Uso En Exteriores (fuera de cualquier recinto) with Weber®. Este asador NO es Weber® y NO esta asociado de ninguna manera con el asador Weber®. Sunbeam® is a registered trademark of Sunbeam Products, Inc. used under license. Sunbeam® es una marca registrada de Sunbeam Products, Inc. utilizada bajo licencia. Contact 1-800-762-1142 for assistance. Do not return to p
El reemplazo se realizara por un producto o componente nuevo o reparado. Si el producto ya no estuviera disponible, se lo reemplazara por un producto similar de valor igual o superior. Esta es su garantia exclusiva. La garantia es valida para el comprador minorista original a partir de la fecha de compra inicial y la misma no es transferible. Conserve el recibo de compra original. Para solicitar servicio en garantia se requiere presentar un recibo de compra. Los agentes y centros de servicio de
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar da
Therefore the espresso machine will require occasional descaling. It is recommended that the espresso machine is descaled every 4-6 months, this will vary depending on the frequency of use. Descaling solution Use any of the following when descaling the espresso machine: . Sunbeam Espresso Machine Descaling Tablets . Sunbeam Liquid Descaler, or . Vinegar Solution. Descaling the espresso machine Note: Ensure the espresso machine is turned off and the power cord is unplugged. 1. Remove the water re
Deposits of these oils build up over time and affect the taste of the coffee and operation of the espresso machine. Regular cleaning to remove these oils is essential and will maintain the quality of the coffee the espresso machine produces and result in less maintenance being required. This is easy to do by following a few quick and easy cleaning steps after each coffee making session; . Cycle water through the group head, . Purge steam through the steam wand, . Wipe the steam wand clean with a
Switching on the machine • Turn the power on at the power outlet and switch the espresso machine on by pressing the ‘POWER’ button on the control panel. See figure 8. LCD: Indicates briefly <
Snap pedestal into the bottom of the heater housing. Refer to Figure 1, 2. Base Assembly Step 1: If the base is in two halves, snap them together by sliding slots of one base half into slots of second base half. Refer to Figure 3. Step 2: Run the power cord through the center of the assembled base. To assemble the base to the unit (either one or two-piece base) first make sure the side marked “Rear” is facing the back of the heater. Line up holes of the base with holes on bottom of pedestal (or