2. Asegurese de que los reflectores laterales apunten hacia afuera desde los costados del remolque. Utilice la luz lateral izquierdas/del lado de la carretera para insertar las cabezas de los pernos de montaje en las ranuras de la parte trasera del bastidor. Pase el cable y los pernos de montaje a traves de los orifi cios del soporte para la placa de matricula e instale en el remolque utilizando tuercas de cierre. Instale la luz con el cable verde del lado del pasajero, el lado derecho del remol

This system is designed to satisfy the needs of the boater for a functional means of transferring “gray” water from the shower, or other water drains. Multiple inlets can be hooked up to more than one drain with different hose size options. The see-through top on the box allows you to see when the filter needs cleaning. Refer to the chart below to ensure that you have selected the proper shower sump for your boat application: Shower Sump D.C. Voltage D.C. Amps Max Fuse Model Amperages 4137 12.0

File around the fitting inside diameter to remove burrs and rough edges. Figure 1 Deluxe Shower Sump System 4137, 4138 Mounting Instructions Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s best-known boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69274 Rev. K 98-08 The Attwood Deluxe Shower Sump System

Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 2/22/2007. 1 nautical mile visibility. 2NM Bi-Color Combination Bow Light For boats up to 20 meters / 65.6 feet. Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 3/6/2007. 2 nautical mile visibility. 2NM Sidelights For boats up to 50 meters / 164 feet. Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable stan

(See Figure 2). 2. Assemble gasket to base. Cover Screw Stainless Steel Lens Cover Telltale Post Housing Vertical Tab, Aligned with Boat Centerline Mounting Screw Base Base Tabs Gasket Butt-Joint Connectors 3/8" Hole, Aligned with Boat Centerline 3. Align hole beneath light base with the position you’ve marked for the wire clearance hole. Set the lamp toward the bow and align vertical tab with the boat centerline. 4. Use the light base as a template to mark locations for the mounting screw pilot

2 nautical mile visibility. REQUIRED FOR INSTALLATION • Phillips screwdriver • Drill and bits: 3/8" for wire clearance hole • Pilot drill for mounting screws • Two #10 pan head stainless steel screws (not included) LOCATION 1. Position light(s) on a surface of the gunwale or deck that is horizontal (within +/-5 degrees). 2. When installing bicolor combination light, place it on the centerline of the boat at the bow (See Figure 1a). When installing sidelight pairs, place lights with the red lens

Make connections according to WIRING INSTRUCTIONS below. 3. Feed the positive (red or gray) and negative (black) wires through the hole in base and lead them below deck. 4. Lower the housing onto the base. Seat the housing so the base tabs fit in the housing grooves and the base screw mount aligns with the housing screw hole. 5. Replace the stainless steel cover, then fasten it with the Phillips-head screw. WIRING INSTRUCTIONS The power supply must be 12-volt DC ONLY. Use crimp-type marine-grade

• Fuse must be 1-amp. 2. Note that navigation rules require sidelights to be operated separately from anchor lights. Use either two switches or a single switch with three positions for off/anchor/running. Figure 3 (pos) (neg)(pos) 12V DC 1-Amp Fuse Switch Green Red (Starboard) (Port) ATTWOOD LIMITED 10-YEAR WARRANTY Because of the longevity of Attwood’s LED lighting technology, Attwood offers a limited 10-year warranty on this LED lighting product. See Product Catalog or attwoodmarine.com for de

Cambie el tipo de base (si es necesario) sobre la base plegable Las versiones embaladas de la luz se envian con la base horizontal instalada. Para cambiar a la base vertical: 1. Quite cuidadosamente el tornillo con leva de fi jacion y la arandela alargada. Separelos para la reinstalacion (fi gura 2). 2. Gire el eje base hacia afuera del portalamparas. Observe la posicion de los 2 cables en la ranura de la base. Quite la base horizontal. 3. Introduzca los cables a traves de la ranura de la base v