-Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local and national codes and ordinances. -Please ensure that this product is properly grounded. -The installer should leave these instructions with the consumer who should retain for local inspector's use and for future reference. -The electrical plug should always be accessible. Installation must conform with local codes or in the absence of codes, the National Fuel G

Manual ignition: Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure. Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star (large flame) and place a lit match up to the burner. Automatic electric ignition: Turn the knob that corresponds to the burner selected anticlockwise direction to the MAXIMUM position at the etched star (large flame) and then press the knob down to activate

3) Insert the 2 nuts in the holes on the lower part of the long pipe. Put the long pipe over the short one (Pict.4/E) by pulling a part the laterals of the pipe. 4) Fix the long pipe wilh 2 serews on the hood (Pict. 4/Q). Attention: The panel should be fitted over the body after installation and fixed using the special screws, (Pict. 5). Electrlc connectlon Attention:The appliance is provided with a supply cord and plug, the appliances must be positioned so that the plug is accessible. Attention

-The evacuated air must not be let into a warm air ducl. -This appliance must be connected to a system equipped with earth or ground plate. -When performing maintenance operations, disconnect the appliance from the field connection. - Do not do any flambe cooking underneath the hood. - When frying, never leave the pan alone because the cooking oil could flare up. - Clean ali the surfaces frequently to avoid danger of Fire. To do so use a cloth and or brush soaked in denatured ethyl alcohol. It i

In addition, exhaust air must not be discharged into a wall cavity unless designed for the purpose. Note instructions for cleaning fan as note «4» on «MAINTENANCE». Moreover it is important to clean regularly each filter of the hood or replace it. N.B. THE RANGEHOOD IS DESIGNED FOR INDOOR USE ONLY. UNDER NO CIRCUMSTANCES SHOULD THIS UNIT BE INSTALLED IN OUTDOOR CONDITION OR OVER A BARBECUE. 1)READ AND SAVE THESE INSTRUCTIONS 2)WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: A. Never lea

La utilizacion de otra tipologia de detergentes exime al fabricante de la responsabilidad de los danos que se puedan derivar. B CARACTERISTICAS TECNICAS Los datos tecnicos del electrodomestico estan contenidos en las placas, situadas en la parte interior de la campana extractora. C INSTALACION (Parte reservada exclusivamente a personas cualificadas). Distancia minima: distancia entre la superficie del soporte de los recipientes de coccion y la parte mas inferior de la campana. Si la campana se c

• Despues de 30 horas de funcionamiento aproximadamente el pulsador propone el lavado de los filtros metalicos (pulsador iluminado de rojo). Para desactivar la alarma pulsar el pulsador por algunos segundos hasta que la luz roja se apaga. A continuacion pare la campana y vuelva a ponerla en marcha para comrpobar que la alarma ha quedado anulada. H FILTROS INSTRUCCIONES PARA EXTRACCION Y SUSTITUCION 1. FILTROS METALICOS Abrir el panel (ver fig. H3). Para quitar el filtro metalico antigrasa utiliz

(44) 01308 423441 Congratulations on your choice of an Aarrow Stove. More than 20 years experience has been put into the development of our Acorn Multifuel to ensure ultimate performance and years of trouble free enjoyment. Every detail on the fire has been carefully engineered and designed which is why we are so confident in the reliability of our product that we offer a 3 year guarantee. Should you have any questions about our Acorn Stoves that are not covered in this manual, please contact th

Open the valve on the gas supply. Using a soap and water solution check each gas connection one at the time, by brushing the solution over the connection. Presence of bubbles will indicate a leak. Tighten the fitting and recheck for leaks. If it is not possible to correct the leak, replace fitting. Under no circumstances use matches or flame for checking leaks. It is essential that the gasket and the pressure test point stopper are properly installed to avoid gas leakage Fig.5B Inches mm A 1 9/1

Operating in this way the gas regulator is converted for use with the other gas/pressure. Service & maintenance instructions Service and maintenance only to be carried out by an authorised person To replace parts such as burners, valves and electric components, the hotplate must be removed from the bench top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing the hotplate attachments nuts which are visible at the bottom of the surface, removing the hotpl