Contact a qualified service person to do this. All local codes must be followed. ! WARNING Fan accessory must be grounded. Fan comes with a three-prong, grounding plug as shown in Figure 1. The plug is your protection against electrical shock. Plug it into a standard, three-hole, grounded, outlet. If cord needs replacing, use only a cord with a three-prong, grounding plug. Grounding Plug Grounded Outlet Figure 1 - Grounding Plug Attaching Fan Accessory 1. Knock out center panel at four tabs with

you can control the room temperature with the thermostat .. . Turn the Thermostat . to the "max“ position. As soon as the desire room temperature is reached... . Turn the Thermostat . back till you hear an audible click. The in-built thermostat now ensures a constant room temperature. Flame regulator With the Flame regulator . you can regulate the flame to any size. . Turn the Flame regulator . in the clock-wise direction until the desired flame size is obtained. Replacing the bulbs Danger of l

Trigger This tool has an easy squeeze trigger. The trigger is located underneath the hand grip. Each squeeze of the trigger fires one staple. Make sure your finger is not on the trigger when connecting or loading the tool. ON/OFF Trigger Lock This tool is equipped with a sliding ON/OFF trigger lock. The trigger lock is located at the front of the hand grip, just above the trigger. This safety feature helps prevent accidental firing. Make sure the trigger lock reads OFF when plugging in or loadin

You can also visit DESA’s technical service web site at 3. Align shim under adjusting plate as shown in Figure 1. 4. Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 1). 5. Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 1). 6. While firmly holding edges of trim together, tighten both screws on the adjusting plate using a slotted screwdriver. 7. Repeat steps 2 through 6 for other side. 8. Place the assembled trim

2. Este calefactor es para USO GENERAL UNICAMENTE. 3. Asegurese que la fuente de alimentacion cumpla con los requerimientos electricos del calefactor. 4. Se debe tener sumo cuidado cuando un calefactor sea usado por o cerca de ninos o personas minusvalidas, y en cualquier momento que el calefactor funcione desatendido. 5. El cordon electrico tiene un enchufe de tres clavijas con puesta a tierra que debe insertarse en un receptaculo Rev. A 4/03 correspondiente. Bajo ninguna circunstancia debe cor

Remove upper shell (see page 8). 2. Remove filter end cover screws using 5/16" nut-driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut-driver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .003"/.004" if needed (see Figure 13). Note: Rotate rotor one full turn to insure the gap is .003"/.004" at tight

SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length of 1-1/2” NPT pipe. Simply substitute your pipe for the provided threaded pipe. 1. Locate the Pipe Mounting Flange, securely mount to ceiling structure. Ensure ceiling structure can safely support the installed Fan. 2. Open one

One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY W

GRILL AND BLADE ASSEMBLY (Figures 3 and 4) NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non- oscillating motor. One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Moto

com PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT. SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length o