3 Important Information .......................................................................................... 4 How the Backup Sensors Work ........................................................................... 5 Limitations ............................................................................................................ 8 Operation ........................................................................................................... 10 Daily Inspection.................

ng and Sheathing, Roofing and Decking PC2012 5.5 hp Honda® Engine Wheelbarrow Oil-Splash Compressor Powerful wheelbarrow oil splash compressor with 5.5 hp Honda engine for superior performance. Benefits • Durable cast iron cylinder for extended wear • Air shroud for cooler running pump and superior heat dissipation • 9.8 cfm @ 40 psi; 8.9 cfm @ 100 psi Applications Framing and Sheathing, Roofing and Decking Contractor Series PC2013 2.0 hp Wheelbarrow Oil-Splash Compressor Powerful

nce. Benefits • Two stage for ultra-fast pump-up and recovery • Durable cast iron cylinder for extended wear • 8.0 Honda® gas engine for superior performance • Oil-splash pump for extended life • Runs multiple tools simultaneously • 17.0 cfm @ 40 psi 16.3 cfm @ 100 psi Applications Framing and sheathing, Roofing and Decking Contractor Series Contractor Series

ht distribution with 8.O gallon capacity • Idle control allows engine to run at low RPM • 12.4 cfm @ 4O psi 1O.4 cfm @ 1OO psi Applications Framing and Sheathing, Roofing and Decking PC2G15 8.G hp Honda® Engine Wheelbarrow Oil-Splash Compressor Powerful wheelbarrow oil-splash compressor with 8.0 hp Honda engine for superior performance. Benefits • Two stage for ultra-fast pump-up and recovery • Durable cast iron cylinder for extended wear • 8.0 Honda® gas engine for superior performanc

Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. The manual should be considered a permanent part of the tiller and remain with the tiller when sold. Read the manual carefully. Pay special attention to statements preceded by the following words: - Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed. CAUTION: Indicates a possibility of personal injury or equipment damage

All information in this publication is based on the latest product information available at the time of approval for printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. The illustrations in this book are based on the WB20X unless otherwise noted. No part of this publication may be reproduced without written permission. This manual should be considered a permanent part of the pump and should remain with the pump if it

Extended dry operation will destroy the pump seal. If the unit has been operated dry, stop the engine immediately and allow the pump to cool before adding priming water. PRIMING WATER 4. STARTING THE ENGINE 1. Turn the fuel valve ON. 2. Close the choke lever. NOTE: Do not use the choke if the engine is warm or the ambient temperature is high. ; FUEL VALVE CHQKE LEVER 3. Turn the engine switch to‘the ON position. 4. Move the throttle lever slightly to the left. THROTTLE LEVER 5. Pull the starter

l Never run the engine in an enclosed or confined area. Exhaust gas contains poisonous carbon monoxide gas; exposure can cause loss of consciousness and may lead to death. l The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Be careful not to touch the muffler while it is hot. Let the engine cool before storing the pump indoors. l A spark arrester is available as an optional part for this pump. It is illegal in some areas to operate an engine wit

All information in this publication is based on the latest product information available at the time of approval for printing. Honda motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. This manual should be considered a permanent part of the tiller and remain with the tiller when sold. Pay special attention to statements preceded by the following words: Enm In

Remove water and sediment from the filter screen and fuel strainer. / 4. Reinstall the fuel strainer, reconnect the fuel lines and secure them with the clips. NOTE: Turn the fuel valve ON and check for leaks. 7. Rotor assembly Install the tine assemblies and side disks as illustrated below. NOTE: Use of the side disks is optional. They are designed to enhance till- ing operations and their use is recommended to: 1) keep the tiller aligned for furrowing (especially on slopes); 2) protect plants a