The test data from which it has been calculated has been certified by 0087. 10 © Baxi Heating UK Ltd 2008 Inlet Pressure (Natural Gas - G20) mbar 20 Injector (Natural Gas - G20) 7.5mm (24&28 model) 12mm(33 model) Electrical Supply 230V~ 50Hz (Appliance must be connected to an earthed supply) Power Consumption 155W (24 & 28 model) 160W (33 model) Electrical Protection IPX0D External Fuse Rating 3A Internal Fuse Rating F2L Condensate Drain To accept 21.5mm (3/4 in) plastic waste pipe Flue Terminal

It should be connected to the system, preferably at the same point as the expansion vessel. Its location should be visible from the filling point. © Baxi Heating UK Ltd 2009 4.0 System Details Temporary Hose Mains Water Stop Supply Valve (Service Pipe) Double Check Valve Heating System Filling a Sealed Water System (Method 1) Mains Topping Up Method NOTE: This method of filling a sealed system Fig. 7 may only be used if acceptable to Local Water Undertaking Hose Union Mains Water Supply Cistern

27). 20. Using a suitable bit (e.g. 2mm), drill through the extension and outlet. Secure using two of the screws supplied. 21. The remaining screw must be used to secure the adaptor to the concentric terminal. 22. When the plume outlet is positioned under a balcony or other projection (Fig. 28) it must protrude at least 200mm (it is not necessary to extend it further than this). 23. When under balconies or projections it is permissible to rotate the concentric flue length up to 70°, clockwise or

Slide the expansion vessel and insulation out of the retaining clips. 7. Reassemble in reverse order using new sealing washers. Fully recommission the appliance and system. 12.17 Condensate Trap (Fig. 63) 1. Disconnect the two sensing wires from the trap connections. 2. Squeeze together the wire spring clip to release and ease the inlet pipe from the trap spigot. 3. Undo the nut securing the condensate drain pipe to the trap. Disconnect the pipe and sealing washer. 4. From underneath the boiler

Creating efficient heating and hot water solutions is The next generation BaxiBermuda Back Boiler Unit Bermuda BBU HE a range that includes traditional and contemporary styles, from stand-alone units to suites and surrounds. Together with Baxi boilers, they provide a complete Gas Industry Innovation Award 2010 Baxi’s commitment to innovation, technology and excellence has defined the company since 1866. Creating efficient heating and hot water solutions is The next generation BaxiBermuda Back Bo

Product/Production certified by: Notified Body 0086. For use in GB/IE only. These instructions include the Benchmark Commissioning Checklist and should be left with the User for safe keeping. Natural Gas Potterton Performa 24 Eco HE G.C.No 47 393 11 CONTENTS Section Page Legislation 4 1.0 Introduction 5 2.0 General Layout 6 3.0 Appliance Operation 7 4.0 Technical Data 8 5.0 Dimensions and Fixings 9 6.0 System Details 10 7.0 Site Requirements 13 8.0 Installation 19 9.0 Commissioning 24 10.0 Compl

Error codes that are shown as automatic reset will disappear once the fault has cleared. The appliance will restart if there is a demand except in the case of errors 263 and 264 when the appliance must be switched off and on again to enable a restart. All other error codes indicate a fault condition, which will require the attention of a service engineer. © Baxi Heating UK Ltd 2010 12.0 Care of the Boiler Warning ! If you smell gas Do not operate light switches Do not operate any electrical equi

In IE, this must be carried out by a competent person as stated in I.S. 813 “Domestic Gas Installations”. Lifting -This product should be lifted and handled by two people. Stooping should be avoided and protective equipment worn where necessary. Carrying & lifting equipment should be used as required, e.g. when installing in a loft space. The addition of anything that may interfere with the normal operation of the appliance without express written permission from the manufacturer or his agent co

7 Fig. 8 Reset OFF Position Fig. 6 Fig. 5 Fig. 4 2 1 0 4 3 bar Power On Neon Burner On Neon Central Heating System Pressure Gauge Position (i) (Central Heating or Hot Water) On/Off/Reset Selector Switch Central Heating Neon Domestic Hot Water Neon 30o 40o 50o 60o 70o 80o 6 7 8 9 10 11 3.0 Operating the Boiler 7 3.2 Temperature Control 1. Central Heating: The central heating hot water flow temperature can be adjusted between 30° C (± 5° C) minimum and 85° C (± 5° C) maximum. 2. Turn the control k

The heating will operate when the white tappets are set to the outer edge of the bezel. To ensure the heating stays OFF set the required tappets inwards towards the centre of the bezel. Each tappet represents 15 minutes. For example: If the heating is not required between 10 A.M. and 11 A.M. the four tappets anticlockwise from the 10 A.M. will be set inwards (Fig. 7). 2 3 4 5 AM 7 8 9 10 0 9 10 11 12 4 Constant Time Pointer Timed Off Rotate to adjust time Off Position On Position Time Pointer Fi