Rinse thoroughly. 4. Remove the valve and tee from the bottom of the kettle by removing the clamp. Remove o-rings. Wash and dry thoroughly. When re-installing the valve, apply USDA approved food grade grease (Chesterton 622 or equal) to o-rings. Gently push tee and valve body in place and secure with clamps. 5. Clean outer drive shaft seal on the side of the kettle by removing thumb screws. Slide seal retainer plate and quad ring away from the kettle or shaft housing. Clean the shaft, seal and q

(Please specify remote mounted control center or kettle mounted control center.) Standard Features for Kettle Control Center: ¦ Solid State temperature control with digital read-out ¦ Time/Temperature Chart Recorder to provide permanent record of Batch Processing ¦ Automatic and manual steam control ¦ Automatic and manual jacket water cooling ¦ Simmer control for delicate products ¦ Automatic water meter with accumulative “add on” button and digital readout ¦ U.L. approved Options & Accessories

COOK/CHILL HORIZONTAL AGITATOR STATIONARY MIXER KETTLES Cleveland Standard Features ¦ Full 60, 100, 150, 200 or 300 gallon working capacity ¦ Electrically driven, Horizontal Agitator Mixer Arm ¦ Variable mixer speed control ¦ Spring loaded blades scrape entire heated surface area ¦ Internal mixing fins for most efficient, uniform mixing, heating and cooling ¦ Flush mounted, easily removable temperature probe ¦ Simmer control for cooking delicate products ¦ 3” diameter air operated, flush mounted

LISTING (NOT TO SCALE) Cleveland Range, LLC. 1333 East 179th Street Cleveland, OH 44110 Phone: (216) 481-4900 Fax: (216) 481-3782 MIXER KETTLES Kettle Placement • Level • Centered on hoist rail • All legs bolted to floor • Gear box properly supported • Proper clearance • Pasta basket and batch bucket clearances • Floor drains and poor paths Electrical Requirements • Voltage • Phase • Amp draw • Wire Size • Check motor rotation Water requirements 1. Hot and cold water supply (Potable) • Line size

24 hour chart recorder 4. KETTLE RUN push button 5. Agitator speed control with variable settings 6. Agitator STOP/START 7. Potable water meter with OFF/ON switch and push button to add water 8. Manual COOL water switch 9. Kettle selector switch for CONTINUOUS, OFF, COOK 10. SIMMER switch 11. Product VALVE OPEN/CLOSED Operating the Kettle 1. To operate the system the main power switch on the control panel must be turned on. The temperature control computer will run through its diagnostics for ab

Incoming power (220 VAC) is sent through the 2A fuse (F1.1) to The 12 vdc power supply (G1) 12vdc is sent to terminals 3 and 4 of the connector X10 on the Control Board (A10) Terminal 1 of connector X12 on the Control Board (A10) Terminal 10 of connector X13 on the Control Board (A10) The return of the Supply is sent to terminal 7 of connector X13 on the Control Board (A10) With 220 VAC to the Control Board (A10) The Operation Board (A11) is energized An alarm will sound for one second All the L

The normally closed auxiliary contacts of both K55 and K56 open preventing the K57 contactor from energizing. If the combi fan is in the reduced setting 220 VAC is sent from terminal 6 on connector X11 through the normally closed auxiliary contacts of contactors K55 and K56 to the coil of contactor K57 The K57 contactor closes Sending 220 VAC through the Q57 thermal overload to the motor and the motor turns at a reduced speed. The normally closed auxiliary contacts of K57 open preventing the K55

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Instructions for Casters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleveland Range, LLC has made every effort to provide accurate information in this document, but cannot guarantee that this document does not contain unintentional errors and omissions. The information in this document may be subject to technical and technological changes, revisions, or updates. Cleveland Range, LLC assumes no liability or responsibility regarding errata, changes, revisions, or updates. Qualified Cleveland Range, LLC Authorized Service Representatives are obligated to follow ind

A red light glows when electricity is on. If water level is correct steam generator will operate by pressing the “reset" button. Heaters will not work without water in the steam generator. This manual reset button must be pressed to start up the generator initially, and to restart the steam generator after every shut off. or power interruption. No attempt should be made to operate the equipment during a power failure. 8) Check to make sure that the water in the sight gauge glass automatically s