Before dismounting always lock the brake pedal and turn the ignition “OFF.” Also disengage the power take-off control switch. 11 A CAUTION Always engage brake pedal lock, lower equipment and shut off engine before dismounting. Never start engine from ground. OPERATING THE FRONT POWER TAKE-OFF CLUTCH (PTO) NOTE: Be certain to follow break-in instructions, listed below. 1. Move the throttle lever back to the medium or “SLOW” position. 2. Flip the toggle switch to the “ON” position. 3. Adva

Carburetor not adjusted properly. Loss of power 1. Connect and tighten spark plug wire. 2. Remove ice and snow from gas cap. Be certain vent hole is clear. 3. Contact Service Center. 1. Spark plug wire loose. 2. Gas cap vent hole plugged. 3. Exhaust port plugged. Unit fails to propel itself 1. Adjust drive control cable. Refer to “Adjustments”. 2. Replace drive belt. 1. Drive control cable in need of adjustment. 2. Drive belt loose or damaged. Excessive Vibration 1. Loose parts or damaged auger.

Si no esta seguro acerca de estos procedimientos, lleve su unidad a un establecimiento de reparacion, persona o distribuidor de servicio autorizado que arregle motores para uso fuera de la carretera. NOTA: El mantenimiento, la sustitucion o arreglo de dispositivos para el control de emisiones y sistemas pueden ser hechos por cualquier establecimiento de reparacion, persona o proveedor de servicio autorizado que arregle motores para uso fuera de la carretera. ADVERTENCIA: Para evitar lesiones per

Under any adverse conditions, do not attempt to free the tractor by speeding up the engine and suddenly engaging the clutch. Try backing out CAUTION! Do not carry passengers or give rides. Keep children, pets, and bystanders a safe distance away. STOPPING THE TRACTOR Disengage the clutch by pressing the pedal all the way down. Move the gearshift lever to the "N" position. Before dismounting always lock the pedal, disengage the power take-off, and turn the ignition "OFF". CREEPER SHIFT LEVER

Refer to "SPECIFICATIONS" when replacement is necessary. To replace the taillight lamp, remove the lens from the taillight and replace. Refer to "SPECIFICATIONS". FUSE (Electric Lighting) Always use the same capacity fuse for replacement. Refer to "Specifications". If the lights fail, check the fuse. The fuse is located in a fuse housing in the line at the back of the instrument panel. To install a new fuse, press in on the fuse housing cap and turn counterclockwise to remove it from the fu

Be sure to observe and follow these precautionary instructions. The discharge shield on the mower must be attached at all times while operating the mower. Keep the machine in good operating condition and keep safety devices in place. Use guards or shields as instructed in Operator's Manual. Children should not be allowed to operate the mower unless properly supervised, and are physically and mentally capable of safe operation. Never place hands or feet under the mower, in the discharge chute

This oil may be used for the first 30 hours of engine operation at temperatures between +90 degrees F. and 0 degrees F. If temperatures are not within this range, drain the oil from the crankcase and replace with new oil as specified in the "Lubrication Table". The engine oil must be drained and replaced with new oil every 30 hours of engine operation. We recommend I.H. No. 1® Engine Oil. If other than I.H. No. 1® Engine Oil is used, it must be designated "For Service MS". In new API Code these

The material has been prepared in detail to help you better understand the correct care and efficient operation of your tractor. Before you operate the tractor, study this manual carefully. New copies may be ordered from your dealer at a nominal price. Your local International Harvester dealer is interested in the performance you receive from this tractor. He has factory-trained servicemen, informed in the latest method of servicing tractors, modern tools, and original-equipment IH service part

See Figure 8. Skid Shoe The position of the skid shoe is determined by the condition of the ground from where snow has to be removed. See Figure 8. Shift Lever The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel. It can be moved into any of eight positions. See Figure 8. Forward Your snow thrower has six forward (F) speeds. Position number one (1) is the slowest. Position number six (6) is the fastest. Reverse Your snow

• Re-install frame cover and flip the snow thrower back to the operating position. • Wrap auger belt around the engine pulley. • Re-install belt cover with self-tapping screws removed before. Figure 25 Drive Belt • Remove belt cover by removing the two selftapping screws that secure it to the snow thrower frame. See Figure 22. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Take auger belt off the pulley as shown in Figure 23 Self-tapping Screws Engin