17 localizados en la base de la taladradora. Fig. 17 DE FUNCIONAMIENTO CONTROLES Y AJUSTES INTERRUPTOR El interruptor (A) Fig. 18 esta localizado en la parte delantera del cabezal de la taladradora. Para ENCENDER la taladradora, mueva el interruptor a la posicion elevada. Para APAGAR la taladradora, mueva el interruptor a la posicion inferior. A A Fig. 18 27 BLOQUEANDO EL INTERRUPTOR EN LA POSICION DE APAGADO IMPORTANTE: Cuando la herramienta no es adentro uso, el interruptor se debe bloquear en

12. MANTENGA las manos y los dedos alejados de labroca taladradora o la herramienta de corte. 13. NO INTENTE taladrar material que no tenga una superficie plana contra la mesa. FIJE CON ABRAZADERAS LA PIEZA DE TRABAJO o sujetelacontra la columna para impedir que gire. Ademas, sujete con abrazaderas la pieza de trabajo cuandoutilice una sierra perforadora o una herramienta decorte de mas de 1/2 pulgada de diametro. 14. DETENGA la taladradora siempre antes de quitar laspiezas descartadas de la mes

Box 168 803-271-9000 Myrtle Beach 29577 Coastal Elec. & Rewinding 718 8th Avenue N. 803-448-3586 Spartanburg 29302 Cash Supply 113 Country Club Rd 803-585-9326 SOUTH DAKOTA Rapid City 57702 Stan Houston Equipment Co. 1210 Deadwood Avenue 605-348-1155 Sioux Falls 57702 Sian Houston Equip. Co 501 S Marrion Road 605-336-3727 TENNESSEE Chattanooga 37412 F & D Tool Service and Supply 4121 Ringgold Road 615-698-6454 Clarksville 37042 Opa's Shop 312 Pine Mountain Road 615-647-5842 Jackso

434-08-651-0006 ©Delta International Machinery Corp. 1997 12" Variable Speed Wood Lathe (46-700 Bench Model) (46-701 Floor Model) INSTRUCTION MANUAL TABLE OF CONTENTS SAFETY RULES...............................................................................................................................................................3 ADDITIONAL SAFETY RULES FOR WOOD LATHES...................................................................................................4 UNPACKING AN

II is equipped with a brass plug on one end and a comfortable knob on the other. IMPORTANT: NEVER DRIVE THE WORKPIECE INTO THE SPUR CENTER WHEN IT IS MOUNTED IN THE HEADSTOCK. Instructions on setting the spur center into the workpiece are found in the “OPERATION” section of this manual. Fig. 29 TAILSTOCK LIVE CENTER The tailstock live center (A) Fig. 31, supplied with your lathe, is equipped with a No. 2 Morse Taper shank and is inserted into the tailstock spindle (B), as shown. To remove the

Indica una situacion potencialmente peligrosa, la cual, si no es evitada, podria resultar en lesiones menores o m o d e - r a d a s . Usado sin el simbolo de seguridad de alerta indica una situa-cion potencialmente riesgosa la que, si no es evitada, podria causar danos en la pro p i e d a d . PROPOSICION DE CALIFORNIA 65 Algunas particulas originadas al lijar, aserrar, amolar, taladrar y realizar otras actividades de construccion contienen productos quimicos que producen cancer, defectos de naci

HERRAMIENTAS DE ENSAMBLAJE REQUERIDAS 1/8" Llave Inglesa Hexagonal (suministro) El Destornillador de Phillips 6 Mm Llave Inglesa Hexagonal (suministro) la Llave Inglesa Ajustable ESTIMACION DEL TIEMPO DE ENSAMBLAJE Menos de 1 hora AJUSTANDO LA TENSION DE CORREA Su lijadora se envia de fabrica con la correa de marcha (A) Fig. 2 ensamblada a ambas poleas (B) y (C). Antes de ensamblar la unidad de disco a la maquina, revise y ajuste la tension de correa: 1. Afloje el tornillo (D) Fig. 1 con la 6 Mm

and Model No. plate is attached to the top surface of the frame casting. This plate can be seen by removing the front guard and looking behind the left edge of the upper blade wheel. Locate this plate and record the Serial No. and Model No. in your manual for futur^ reference. SERIAL NO. _ MODEL NO__ PART NO. 1088294 DATED 5-25-77 SAFETY RULES FOR ALL TOOLS As with all power tools there is a certain amount of hazard involved with the operator and his use of the tool. Using the tool with th

Current models have stamped sheet metal blower housings. D - When screw requires servicing install at 100 inch lbs 10 REPLACEMENT PARTS 50-185 BAG ASSEMBLY ----------- (OPTIONAL FOR 50-180 & 50-181 - STANDARD FOR 50-182) REF № PART NUMBER 50-185 1 50-188 2 410-06-027-00001 3 410-06-105-0001 4 50-195 OESCRIPTIQN DRUM MOUNTED DUST BAG, CONST OF: HOSE, INCL; CLAMP - 6" HOSE SLEEVE DUSTBAG NOT SHOWN ASSEMBLED NOTE: THE NECK OF THE BAG MUST BE CLAMPED TO THE DRUM USING A STANDARD 55

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou