Sacar todos los elementos necesarios por el montaje de la bollita de plastico 3. Insertar el O-ring grande en el tallo del mezclador y colocar el mezclador donde deseado NOTA: El O-ring de goma tiene que ser insertado entre el plan de montaje y el cuerpo del mezclador. No utilices mastique, u otro sellador, en este punto. 4. Instalar a los miembros de montaje (GR0356031) sobre el tallo fileteado en la secuencia aquii bajo indicada: 1 – mondana plana rotonda en fibra Respaldo perfilado triangular

Averiguar que la palanca y la boca sean alineadas adecuadamente hacia adelante. 6. Apretar la mondana de laton (4) con la llave dotada o utilizar los adecuados instrumentos. NOTA: INSTALACION SOBRE SUPERFICIES SOLIDAS: la parte de abajo al plan de apoyo tiene que ser llana y falto de virutas; en caso contrario el mezclador no podra ser colocado adecuadamente en la misma sede. INSTALACION SOBRE BALDOSAS: Evitar l’ instalacion del mezclador cerca de o sobre las fugas. El mezclador podria no result

(1-800-626-5771) or visit TABLE OF CONTENT 1 Faucet 2 Flexible hose of the side spray 3 Hook for side spray 4 Side spray 5 Priority water flow system 6 Fastening set (rubber washer, metal washer, nut) 7 Fastening set (rubber washer, triangular flange, metal washer, nut, allen key 2,5mm) 8 Counter weight 3 ENGLISH Install faucet to the sink or countertop Set the faucet into place on the sink as indicated in the figure. NOTE: the rubber O-ring should be sitting on top of the count

NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit TABLE OF CONTENTS 1 Faucet 2 Wall fastening set 3 Wall flange (over the sink) 4 Wall flange (under the sink) 5 Fastening set (rubber washer, triangular flange, metal washer, nut) 6 Non-return valves 1 5 6 3 4 2 2. Remove all mounting hardware from protecting plastic bag. 3. Place the large O-ring over the faucet shank and place the faucet into the desired location. NOTE: the rubber O-ring should be sitting on top of

Davlumbaz Uzivatelska Poirueka Odsavac par FDB 9078 SIL-K INDEX EN RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 3 CHARACTERISTICS ............................................................................................................................................................. 4 INSTALLATION.............................................................................................

FFP S700 SERIES Pull-Out Spray Faucet Installation guide ENGLISH 2 G 1748.XX G 1782 G 1156 G 29016 G R0239.XX G 13396.XX G R0637 G R1664 G 1636 G 1463 TECHNICAL DATA · Minimum working pressure 0,5 bar · Maximum working pressure 5 bar · Recommended working pressure 3 bar (in case of water pressure higher than 5 bar it is recommended to install pressure reducers) · Maximum working temperature 70°C PARTS LIST G 13396.XX Handle G R0239.XX Ring cap G 1156 Cartridge G R0637 Fastening set (rubber washe

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. Use proper pan size. Always use cookware appropriate for the size of the surface element. WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

Proceed with the following steps: Step 1: Verify that the line and load cables comply with applicable electrical codes. Step 2: Verify that the transfer switch rated current and voltage (see identification plate on the door of the transfer switch) agree with system current and voltage. Step 3: After the transfer switch is mounted, provide the conduit or cable openings as required. Ensure that no metal filings contaminate the transfer switch components. Step 4: Test all power cables before connec

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet PF-1000 and PF-2000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Connection: 1/2. NPT Please read our instruction before

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-3000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Tailpipe connections: 3/8. O.D. Please read our instruction before