L. GO24 Grand Oak Series Logs • Open the log box and remove the paper packaging and logs. • Inspect each log for breakage that may have occurred during shipping and handling. .. .. SRV738 SRV736 .. SRV737 .. .. SRV722 SRV723 .. .. SRV728 SRV724 .. .. SRV742 SRV729 .. .. SRV743 SRV727 M. GO24 Grand Oak Series Log Placement Instructions • Place logs EXACTLY as the following photos depict. WARNING Fire Risk Explosion Risk Personal Injury Risk Failure to position the parts in accordance with these d

Installation Instructions Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trained professionals, or technicians supervised by an NFI certified professional. Models: GO24MTCH,GO30MTCH GO35MTCH, GO40MTCH Grand Oak Match Light Gas Log Sets Check with your local building code agency before you begin installation to ensure compliance with local codes, including the need for permits and follow-up inspec

Ensure that the leveling leg is positioned over the 2 x 4 before leveling the insert. September 1, 2008 7036-135E Page 11 Mt. Vernon Pellet Insert (AE) 4 44V VVent Information ent Informationent Information A. Venting Termination Minimum Requirements R J or XV M I HA V G B V V A B V F V C B B E L V D V Electrical Ser ice V NV N V N N V Inside orner FIXED CLOSEDOPEN OPEN FIXED CLOSED V X G GTermination Cap Air Supply Inlet Gas Meter Restricted Area O P Figure 12.1 All minimum clearances are liste

• Failure to do so could result in smoking, sooting and possible hopper fires. E. Baffle Removal Baffle Latches Insert flat head screw driver into “V” section and push down and the bottom of the latch will fall forward off of post Locating ears - 1 on each side. Fit behind bottom edge. Figure 36.2 WARNING Cast iron is a very heavy material. The baffle is made of cast iron and therefore is heavy and awkward at times to maneuver. Clear and prepare your work area before you begin. a. The appliance

Figure 24.4. 3. Automatic or Manual Setting The automatic setting will control the heat output based on the comfort level selection. The manual setting allows you to manually control the heat output settings. See Ignition Cycles on page 25. NOTE: See the Wall Control Thermostat manual for detailed instructions. FUEL SELECTION Corn Utility PelletSoftwood Pellet Sunflower Seeds Wheat Hardwood Pellet DONE SELECT Figure 24.3 Figure 24.4 Page 24 7036-135E September 1, 2008 R R Mt. Vernon Pellet Inser

29 Auto-Clean Cam, Switch SRV7034-187 30 Switch, Micro, Normally Open 7000-327 31 Motor 12 Volt 7000-300 32 Auto-Clean Motor Grommet 7034-188 Item Description Part Number 1 Door Frame Assembly 7034-026 2 Latch Assembly, Door 7034-039 3 Glass Assembly 7034-007 4 Glass Retainer 7034-136 5 Hinge, Female 450-2910 6 Magnet & Bracket Assembly 7034-008 7 Door Air Deflector 7034-185 Page 42 7036-135E September 1, 2008 R Mt. Vernon Pellet Insert (AE) Figure 42.1 # Description # Description # Description

• Range hoods. • Combustion air requirements for furnaces, water heaters and other combustion appliances. • Clothes dryers. • Location of return-air vents to furnace or air conditioning. • Imbalances of the HVAC air handling system. • Upper level air leaks: recessed lighting, attic hatch opening, duct leaks. WARNING Asphyxiation Risk This appliance produces carbon monoxide (CO). • The free opening areas (in square inches) of the chimney damper as shown in the following tables must be met. • User

(Place lit match in ember bed before turning on valve) (Located in wall or floor near fireplace) Valve KeyValve WARNING Asphyxiation Risk Gas-burning appliances produce smoke and carbon monoxide gas during operation. • The damper must be open • The chimney must draw properly These fumes can be harmful if not vented properly. W. Cleaning and Maintenance Instructions Always remember: • Do not place any combustible material near the appliance. • Do not place any paper, trash or other material on th

. psi (3.5 kPa)) before appliance is connected. Be sure to release air pressure from the gas line before connection is made to the appliance. Excessive pressure will damage the gas control and may cause a gas leak. • Gas Leak Test: Make sure the gas connections are tight. Turn on the gas and coat each joint with a non-corrosive gas leak check solution. Air bubbles will form indicating any leaks. DO NOT USE A FLAME OR ANY TYPE OF IGNITION SOURCE TO CHECK FOR LEAKS. All leaks must be corrected bef

• Replace component parts of the chimney and fireplace as specified by the professionals. • Ensure all joints are properly engaged and the chimmney is properly secured. • Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame pattern. • Do not use a blower insert, heat exchanger insert or other accessories not approved for use with this appliance. B. Tools and Supplies Needed Tools and supplies normally required for installation: Pliers Phillips screwdriv