Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  

Regency G36D

Descargado: 21Tamaño del archivo: 20 mb    Fabricar: Regency  
Categoría: chimeneas

1) Make sure the valve is in the "OFF" position. 2) Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide flat screwdriver. 3) Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose. G36D-NG1 System Data For 0 to 4500 feet altitude Burner Inlet Orifice Sizes: #42 Max. Input Rating 26,000 Btu/h Min. Input Rating 13,100 Btu/h Supply Pressure min.5.0" w.c. Manifold Pressure (High) 3.8"+/- 0.2"w.c. Log Set: Ceramic fibre, 7 per set. Vent System:

Regency E21-NG1

Descargado: 0Tamaño del archivo: 10 mb    Fabricar: Regency  
Categoría: chimeneas

The bay front is a decorative overlay only. 1) Place the bay door onto the 2 pins on the top of the unit. 2) Position 2 magnets on the back of each trim piece close to the ends. Place the top and bottom trim pieces on the bay front. 3) Install top and bottom louvers. Note: Top and bottom louvers and brackets are different. See diagram below. 2) Install bottom louver by sliding the two bracket clips into the brackets located underneath the bay door and secure with 2 screws into the bracket on the

Regency E21-LP1

Descargado: 2Tamaño del archivo: 10 mb    Fabricar: Regency  
Categoría: chimeneas

HILOOFFONPILOTTPTHTHTP To wall switch, remote control or thermostat To thermopile Thermostat Wire Table 14 GA. 16 GA. 18 GA. 20 GA. 22 GA. 50 Ft. 32 Ft. 20 Ft. 12 Ft. 9 Ft. Recommended Maximum Lead Length (Two-Wire) When Using Wall Thermostat (CP-2 System) Wire Size Max. LengthWire Size Max. Length Regency E21 Gas Fireplace Insert OPERATING INSTRUCTIONS FINAL CHECK Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly. This includes: 1) Cloc

Regency B36X

Descargado: 25Tamaño del archivo: 9 mb    Fabricar: Regency  
Categoría: chimeneas

This could cause high temperatures and may present the possibility of a fire. b) The location of the horizontal vent termination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. See "Exterior Vent Termination Locations" section for more details. 7) Ensure that the pipe clearances to combustible materials are maintained (Diagram 5). Install the termination cap. Note: If installing termination on a vinyl siding covered wall, a vinyl siding

Regency SLBV 35/40

Descargado: 7Tamaño del archivo: 6 mb    Fabricar: Regency  
Categoría: chimeneas

Pour empecher l’acces a un foyer ou a un poele, installez une barriere de securite; cette mesure empechera les tout petits, les jeunes enfants et toute autre personne a risque d’avoir acces a la piece et aux surfaces chaudes. Figure 1 Gas Controls / Control Compartment Access Fireplace gas controls are located in the lower control compartment under the firebox (see Figure 1). Remove the control compartment door to access the controls. To remove the control compartment door: Gently pull upward an

Regency SSDVST-CNE-B

Descargado: 0Tamaño del archivo: 5 mb    Fabricar: Regency  
Categoría: chimeneas

Thesizeandpositionofthelog set was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, soot ing, and poor flame quality. Logs get very hot and will remain hot up to one hour after gas supply is turned off. Handle only when logs are cool. Turn off all electricity to the appliance before you install grate, volcanic stone, vermiculite, embers and logs.

Regency SSDVPF-CNM-B

Descargado: 0Tamaño del archivo: 5 mb    Fabricar: Regency  
Categoría: chimeneas

It isrecommended toseal around the gas line to prevent cold air leakage. Gas line connection may be performed largely outside of the confines of the control compartment and without having to enter the firebox behind the glass. Proceed as follows: Acquire the shut-off valve and gas lex line and pull the assembly forward out of the compartment. Separate the shut-off valve from the gas flex-line. Determine the length of pipe needed to route the gas line from the last fitting (shown in Figure 14 on

Regency SSDVPF-CNE-B

Descargado: 0Tamaño del archivo: 5 mb    Fabricar: Regency  
Categoría: chimeneas

These fireplaces are designed as supplemental heaters. Therefore, it is advisable to have an alternate primary heat source when installed in a dwelling. These appliances must not be connected to a chimney or flue serving a separate solid fuel burning appliance. Millivolt Models - The millivolt appliances are manually controlled and feature a spark igniter (piezo) that allows the appliance's pilot gas to be lit without the use of matches or batteries. This system provides continued service in the

Regency SSDVST-CNM-B

Descargado: 4Tamaño del archivo: 5 mb    Fabricar: Regency  
Categoría: chimeneas

Top Flange on Glass Door Bottom Vee-flange Glass Door Glass Door Latch Glass Door Firebox Floor INSTALLING OR REMOVING GLASS DOOR Figure 56 - Note: When installing the glass door, ensure the spacing on both sides are equal. Step 10. BURNER ADJUSTMENTS Flame Appearance and sooting Proper flame appearance is a flame which is blue at the base and becomes yellowish-orange in the body of the flame. When the appliance is first lit, the entire flame may be blue and will gradually turn yellowish- orange

Regency SDV35

Descargado: 4Tamaño del archivo: 5 mb    Fabricar: Regency  
Categoría: chimeneas

Re-secure the lintel to the rear wall of the firebox. WARNING Failure to reinstall and securely tighten cover plate screws could result in leakage of flue products into the living space. Vent cover plate and vent seal plate must remain securely installed on unused vent collar. Failure to do so could result in leakage of flue products into living space. Cover Plate Securing Screws Top Vent Vent Seal Plate Firebox Top (Inside of Appliance) Figure 15 Top Vent Seal & Cover Plate Removal When Using T





Categoría