Comuniqúese con el Departamento de Servicio Técnico de Royal Sovereign (1-800-397-1025) si necesita dicho servicio para la trituradora. No desarme ni repare la máquina usted mismo. Esto puede provocar un incendio 0 una descarga eléctrica. OC Royal / llJ Sovereign INSTRUCCIONES DE SEGURIDAD PRECAUCIÓN A\ No acerque artículos personales a la máquina como cabello largo, corbatas, collares, ni ropa. Esto puede provocar lesiones corporales debido a la máquina. Apague la máquina y desenchufe
Esto permite una protección de seguridad de nivel 3 para sus documentos. Protección Contra Sobrecalentamiento Para garantizar que la trituradora no se sobrecalentará, ésta se apagará automáticamente si se produce un atasco que hace que el motor se caliente o si la máquina ha estado funcionando continuamente durante más de 25 minutos. Cuando la trituradora se apague, se encenderá el indicador de sobrecarga/sobrecalentamiento del motor y se volverá a encender en aproximadamente 30 minutos cuando
Si se enciende el indicador de revise cesta (Check Basket), asegúrese de que la cesta esté correctamente colocada dentro de la trituradora. • • • • • 3 0 § qp * BASKtT hJLL ::HíCKHiKkr' U-tCCOÜ«' l.\MX WJWLK tuvlfi Se insertaron 7 hojas en la entrada del alimentador manual y se atascó. 1. Revise las Especificaciones para asegurarse de que está utilizando el papel correcto. OC Royal / I1J Sovereign ESPECIFICACIONES Nombre del Modelo AFS-800 AFS-850S AFS-800E3K Suministro Eléctrico AC 1
Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left si
(RSC-1650H and RSC-1650HR). Control Buttons 1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1650H and RSC-1650HR) 2. SPEED DISPLAY: Display’s current Speed. 3. TEMPERATURE BUTTON- (RSC-1650H and RSC-1650HR): To change the temperature (max. RSC-1650H: 122°F, 50°C/RSC-1650HR: 266°F, 130°C)ofthe upper roller, press up or down arrow button. 4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the up or down arrow button. 5. RUN: To start the
(Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bott
To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at 1-800-397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating machine. Keep this information for future reference. Failure to comply any of t
There might be the possibility for difference to the above numbers due to the change of voltage or adjustment of tension. 2. COLD LAMINATING 1. Put cold roll film on upper bar.(Set the same as methord of HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. - 2