101A393 DEC, 2005 English English Swing Door Opener USER'S INSTRUCTIONS CONTENT CONTENT Introduction.......................................................................................................................................................................................4 Overview.....................................................................................................................................................................................4 Installation - In Swing.

3.2 Place the operator onto the mounting plate based on the door type. For instance, for in-swing left door, the “IN-SWING LEFT” holes should match the 2 top holes of the operator. 3.3 Secure the operator to the mounting plate with 6 nuts, spring washers and bolts. Slider bracket Note: In-Swing right door installation shown. Note: In-Swing left door installation shown. For In-Swing Left installation, place the top 2 screws of the door opener to these 2 holes. WARNING To avoid possible serious in

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Chec

Once the isolator is removed, the control panel will announce the sensor's status, such as "Zone 1 Sensor 1 Triggered", and corresponding zone LED will flash and buzzer will beep. If the magnetic contact is closed, the beeping will stop. Note: - Both Window/Door Sensors have been programmed at the factory. They are Zone 1 Sensor 1 and Zone 2 Sensor 1. Trigger the sensor and listen to the announcement to determine which one is zone 1 and which is zone 2. Testing: After mounting the sensor, test t

First use the double sided tape to attach the mounting bracket on the windshield or use the visor clip to clip the mounting bracket on the visor, then you can put the remote control on the bracket. The remote control can also be attached to your key ring as a key fob. 7. TRANSMITTER MOUNTING METHOD 6. Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes. LED 2. RECEIVER INSTALLATION (CONT) If the Smart ButtonTM GB-318’s red LED do

visit our FAQ section at or 2. email us at support@skylinkhome.com, or 3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320 CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel : (800) 304-1187 Fax : (800) 286-1320 PAT. D410633 101Z857-001 OCT, 2010 Email : support@skylinkhome.com 6243000B1 SKYLINK TECHNOLOGIES INC. Your Guide to the Emergency Dialer DIAL-ALERTTM MODEL: AD-105 The AD-105 Emergency Dialer contains all the above it

In this package, you will find the following: Crimper Garage Door Transmitter MK-318 (Battery inside) Unplug the power cord of your garage door opener before installation to ensure power is not connected. DO NOT let children use the gargae door Transmitter without adult supervision. Children can injure themselves or others by the garage door. WARNING DO NOT use remote to control the door without safety beams. 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall b

Easy ClipTM Ribbon Wires Wall Button Ribbon Wires Press / lock 3. Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”. 4. If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button. a) Disconnect the existing wall button from the wall. b) Conne

This is a kit with a universal remote control and Smart ButtonTM. In this kit, you will find the following: Unplug the power cord of your garage door opener before installation to ensure power is not connected. DO NOT let children use the gargae door Transmitter without adult supervision. Children can injure themselves or others by the garage door. DO NOT use remote to control the door without safety beams. 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall but

This is a kit with a universal remote control and Smart ButtonTM. In this kit, you will find the following: Remote Control (Battery included) Visor clip 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console. 2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”. NOTE: Ensure the ribbon wires are not twisted but laid flat inside the clip. If your wall button ribbon wires are not the same