= If chemical products or mixtures of product come into contact with the eyes or are swallowed consult a doctor immediately, taking the label of the product with you. = Wash all clothes that come into contact with the chemical, whether diluted or undiluted, thoroughly before using them again. = Don’t smoke, drink or eat when preparing or spraying the mix or near or in the fields treated. = DON’T ENTER THE TANK: the residues of a chemical product can cause poisoning and suffocation. = When sprayi

= connect hose T to deviator D using the union hose adaptor supplied. = turn the lever of deviator D to the filling position. = place the other end of the hose, on which you fitted filter G, in the watering point. = start the power-takeoff leaving pressure regulator C in the draining position (you don’t have to put the pump under pressure). = the filling speed in litres/minute is equal to the delivery of pump P. = visually check the level of the liquid in the tank and after filling stop the pump

It is used as follows: - turn pressure on in TOP-MIX premixer (see paragraph above) -turn lever 6 down and suck the product up. -the product is suctioned, mixed with water under pressure, and directly incorporated in the tank of the machine. -after incorporating the product in the tank, lift lever 6 back to a horizontal position. NOTE:To wash the incorporator, put it in the premixer for a few seconds, performing the hopper washing operations described in paragraph 4.4. 18 unigreen 4.13 WASHING T

= Check the proper tyres inflation (pressure are indicated on tyres) 4.3 TRANSPORTING AND MOVING THE MACHINE Every time you have to lift the machine, before starting the operation, always make sure the lifting gear and the relevant tools and equipment (cables, hooks, etc..) are suitable for lifting the load and check the stability of the same. It is forbidden to unhook and move the machine with the tank full. The dry weight of the machine at the maximum level of fitting and with all the accessor

4 1.1 COMPOSITION OF THE MANUAL ...................................................................................... 4 1.2 GUARANTEE ....................................................................................................................... 4 1.3 PRODUCT RESPONSIBILITY ............................................................................................. 4 1.4 WARNING SIGNS IN THE MANUAL AND ON THE MACHINE............................................4 2 SAFETY REGULATIONS AND

2) bearing one of the marks indicated in the tables of the allowed fittings (see the following paragraph). 3.1 TABLES OF FITTINGS ALLOWED Table N° 18a let you identify the version of your machine indicating the basic equipment and all the possible fittings available (optional). You can also find the other fittings allowed or other versions to meet your requirements in the future. THE EQUIPMENT DEFINED IN THE TABLES OF THIS HANDBOOK (TAB: 18a, page 31) SHOULD BE CONSIDERED BINDING FOR THE VALIDIT

8.2.3 MULTIPLIER LUBRICATION The multiplier and disengaging boxes are normally lubricated in an “oil bath”, in special cases NLGI n.0 grease is used. The viscosity is an essential characteristic of a lubricant oil and this is indicated by the SAE (SOCIETY OF AUTO-MOTIVE ENGINEERS) classification of the oils for gearboxes and differentials. Special additives improve the capacity of the oil to maintain a lubricant film also at high pressures and temperatures. We recommended using SAE 90 oil for th

WARNING: the indications to follow for using chemical products are indicated in paragraph 2.2.1. 4.12.2PREMIXER ON COVER (OPTIONAL): Open the cover and pour all of the chemical powder into the filter, close the cover and open the supply tap until all of the powder has dissolved. 4.12.2PREMIXER ON COVER (OPTIONAL): Open the cover and pour all of the chemical powder into the filter, close the cover and open the supply tap until all of the powder has dissolved. FIG. 15 4.12.4COVER WASHER FOR CHEMIC

5.7.2 HYDRAULIC DRIVEN HEADS On request hydraulic pivoting (inclination 90° roughly) and rotating (max rotation 270°) heads are available. 5.7.3 HYDRAULIC DRIVES The cannon fans can be equipped with hydraulic drives: with the cylinder fitted directly (30° inclination roughly) or a motor with a pinion and chain (180° inclination roughly). 5.7.4 OIL FEED FROMTRACTOR (for hydraulic systems) Connect the delivery and discharge quick-fit coupling to the respective connections, respecting the direction

15,0 17,2 19,6 21,8 23,7 27,0 29,6 20,2 24,8 28,4 31,6 34,8 40,0 44,0ug. sing. 1,88 2,15 2,45 2,72 2,96 3,37 3,70 2,53 3,10 3,55 3,95 4,35 5,00 5,50 Velocita Km/hspeed Litri/haLitri/haLitri/ha Velocita Km/hspeed Velocita Km/hspeed Larghezza di lavoro working width 3 m. 4 m. 5 m. Tab. 3215/0000F N.B. to calculate the different ranges it is sufficient to multiply the value lt/hectare by the corresponding width indicated in the table and divide it by the new width (see chapter 6.3, page 20). unigre