Each band is adjusted by a center detented fader with ± 12dB of gain available, and a master fader controls system gain for that channel. Clip and signal present LEDs, as well as a bypass switch, are also provided on each channel. Inputs and outputs for each channel are via both 1/4" and RCA jacks. The unit can also be rack mounted in only 1 rack space. FEATURES • 2 complete 30 band 1/3 octave equalizers in 1 rack space • Power up delay circuitry protects speakers by eliminating turn-on transien

4 2.1 CONNECTIONS .................................................... 7 2.2 POWER AND PROTECTION .................................. 8 CHAPTER 3: SPECIFICATIONS AND SERVICE 3.0 SPECIFICATIONS................................................. 10 3.0A Architectural and Engineering Specifications........... 11 3.1 MAINTENANCE /REPAIR INFORMATION .............. 10 3.1A Cleaning........................................................................... 10 3.1B Service .................................

For the best possible sound and lowest noise increase the input level control until the input LED lights occasionally. CH2 (4): Controls the input level (volume) of the microphone connected to Input CH 2 (13). Zero is the lowest (quietest) setting, 10 is the highest (loudest).For the best possible sound and lowest noise increase the input level control until the input LED lights occasionally. OUTPUT LEVEL LED INDICATORS (5) For the best sound increase the INPUT LEVEL of CH1 (3) and/or CH2 (4) so

Los platillos Surge son compatibles con una variedad de modulos de bateria y se pueden usar tambien para disparar sonidos en cualquier instrumento MIDI usando una interfaz de “ disparador a MIDI”. 1. Inserte dos extremos en “angulo recto” de los cables estereo de .” (incluidos) en las dos conexiones del alojamiento del disparador de la parte inferior del platillo. 2. Coloque el platillo en un soporte. No use un manguito con este platillo porque ya tiene uno incorporado. Asegurese de que la tira

The Alesis SR-18 Drum Machine sound range covers almost any kind of music and has some interesting drums, hits, electronic drums, percussion and bass sounds. The Alesis SR-18 Drum Machine features 24-voice polyphony, 32MB percussion and bass sounds, built-in effects (reverb, EQ and compression), 12 drum pads, transport controls, value/tempo jog wheel, pattern-trigger pad, drum roll and mute/solo functions, 100 factory and 100 user presets, backlit LCD, 1/4" input, 1/4" aux and headphones output

Some of the key features of the QS include: • 16 MB of Sound ROM standard • Expandable to 32 MB via our 8 MB PCMCIA format QCards • Up to 16 MB of user sample storage available through Flash RAM PCMCIA cards • True 64 Note Polyphony • 4 High Quality Multieffects Busses • ADAT Optical Digital Outputs • 4 Independant Analog Outputs • 4 Realtime Controller Sliders • Built-In Serial port for direct Mac™ or PC connection • Extensive Tracking Generator and Matrix Modulation sections • 88 Note Weighted

About Alesis Matica. Amplifiers Thank you for purchasing an Alesis Matica power amplifier, one of the most advanced and highest value amplifiers available. Your Alesis High Speed, Wide Bandwidth amplifier provides extremely accurate sonic quality as well as measured specifications, but its conservative design and careful attention to electronic protection means that it will continue to operate at top condition without special attention, year after year. Matica amplifiers use the newest generatio

See below for output wiring in Bridged Mono configuration. Audio Installation: Output Wiring Warning: Be sure that the AC power is off prior to connecting or disconnecting any signal wiring. Alesis amplifiers can reliably drive 2 W loads in Stereo mode and 4 W loads in Bridged Mono mode. However, the impedance of a loudspeaker varies with frequency, and its nominal rated impedance is not necessarily its minimum impedance. Some loudspeakers carry both nominal and minimum impedance specifications,

9 3.1 Copy DSP Settings .........................................................................................................................9 3.2 Paste DSP Settings..........................................................................................................................9 3.3 Reset DSP Settings........................................................................................................................10 3.4 Render DSP To Audio File..................................

5. Si conecto un dispositivo a la entrada de linea (LINE) del modulo, enciendalo. 6. No golpee ningun pad ni presione el pedal de control de hi-hat. Encienda el modulo. 7. Si usa altavoces externos, enciendalos. 8. Golpee los pads y ajuste los niveles de volumen de sus dispositivos segun sea necesario. Si utiliza auriculares, ajuste el volumen del modulo con la perilla de VOLUMEN del panel trasero. Si usa altavoces externos, ajuste el volumen del modulo presionando el cuadrante de DATOS, girando