Hd. 10 21 962109 Screw #10-24 x 5/8 22 762045 Clamp - R.H. Shield 1 23 762046 Clamp - L.H. Shield 1 24 767841 Shield 25 768543 Scraper - L.H. 1 26 762044 Clamp - Rear L.H. 1 27 930086 Rivet - 3/16 x .450 28 682006 Lid Clamp Assembly 29 763444 Gasket - Intake Hsg. Flange 1 30 66909A Retainer Assembly 1 31 66908A Retainer Assembly 1 32 66907A Retainer Assembly 1 33 763443 Gasket - Impeller Housing 1 34 930113 Rivet - Pop 1/8 35 962241 Screw - #10-24 x 1/2 36 962747 Screw - 3/

Only 1 51 34267A Gasket - Muffler Mtg. (Honda Only) 1 52 215104 Label - Warning 1 53 215106 Label - Warning 1 55 62812A Extension Assembly Honda 1 57 755721 Nipple - 1/4-18 Short 1 58 822806 Elbow - 90° Street 1 59 170266 Coupling - 1/4 NPT 1 60 ref. Drain Plug (part of engine) 1 61 85702A Screw - 1/4-20 x 1 5/8 Hex St. Cap 2 62 85701A Screw - 1/4-20 x 1 1/2 Hex St. Mach 2 63 764541 Hook - Bag Right 1 64 766740 Pin - Locking 2 65 920284 Nut - 1/4-20 Stop 4 66 763740 Grip - Handle 2

4. Remove the intake cap. WARNING: Do not put your fingers into the housing. Severe injury to the fingers or operator could occur. 5. Use a tool to reach into the intake housing to remove the object. When using the machine on uneven areas, set the casters to an outward position. Optional Equipment To remove heavy metal clippings and sand, use a special bag support and caster assembly (part # 760641). See figure 7. Figure 5 Figure 6 Figure 7 Clarke® Operator's Manual LV-30 Page 7 MAINTENANCE PROC

Follow this procedure to check the oil: 1. Make sure the machine is on level ground. 2. Turn the cap marked "Engine Oil" counterclockwise. 3. Lift the dipstick out of the tube. 4. If the mark is below "OK", add oil. See figure 1. 5. When adding oil, make sure the oil does not pass the mark "FULL" on the dipstick. See the engine manual for the correct type of oil. HOW TO FILL THE GASOLINE TANK WARNING: Fill the gasoline tank in an open area. Do not fill the tank near open flames. Do not fill the

You must have training in the operation of this machine before using it. If you cannot read English, have this manual explained fully before attempting to operate this machine. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764. Form No. 78439A 12/98 CLARKE TECHNOLOGY Printed in the U.S.A. 230 Volt Machine Instructions For Connection To The Power Supply And Th

You must have training in the operation of this machine before using it. If your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine. Si Ud. o sus operadores no pueden leer el Ingles, se hagan explicar este manual completamente antes de tratar el manejo o servicio de esta maquina. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U.S. Inc., 2100 Highway 265, S