This equipment is intended to use indoor. 3. Position the equipment on a clear, leveled surface. Make sure the surfaces are free of objects that may cause tipping over. 4. Always wear appropriate workout clothing when exercising. 5. Disabled person should not use the equipment without a qualified person or physician in attendance. 6. Never use the equipment if it is not functioning properly. 7. Before exercising, always do stretching exercises to properly warm up. 8. Maximum user weight is

Make sure that the Locknuts are in the hexagonal holes in the Frame. 2 5 14 1 30 18Square Holes 2 1 32 3 40 37 36 38 1 38 33 33 41 3 42 1 1Cap 1 Caps 4 4. The Console (7) requires two "AA" batteries (not included). Alkaline batteries are recommended. Refer to the inset drawing. Remove the battery door from the back of the Console. Press two batteries into the battery compartment. Make sure that the negative ends of the batteries (marked O.O) are touching the springs in the battery compartment. R

1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM.........................................................................………. 8 PARTS LIST.....................................................................................................

2 1 Console Wire Console Wire Console Wire 3 1 25 26 29 3 50 26 6 16 26 Console Wire 25 1a 6 3. Attach a Pedal (31) to one of the Pedal Arms (12) with three #8 x 3/4O Round Head Screws (16) as shown. Repeat this step to attach a Pedal to the other Pedal Arm (not shown). 4. Make sure that there are Pedal Arm Bushings (42) in the ends of both Pedal Arms (12). Identify the Left Handlebar (8) (there is a decal on the Left Handlebar for identification). Slide a Handlebar Spacer (39) and one of the Pe

To protect the floor or carpet from damage, place a mat under the stepper. HOW TO USE THE IMAGE. 7.0 STEPPER The stepper console offers a variety of features to help you get the most from your exercise. When the console is in the manual mode, the stepping speed can be changed with a touch of a button. As you exercise, four LED displays will provide continuous exercise feedback. The console also offers six workout programs. Each workout program is designed to change the stepping speed automatical

Find the markings inside the battery compartment showing which direction the batteries must be turned. Insert the batteries into the battery compartment. Attach the Monitor Bracket (27) to the back of the Electronic Monitor (46) with the four Console Screws (44). Insert the Handlebar Shaft (54) into the Frame (1). Plug the Sensor Wire (21) into the wire on the Electronic Monitor (46). Attach the Monitor Bracket with the Monitor to the Frame (1) with two 3/16O Small Screws (2). Make sure that the

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Pedal Side Shield Link Arm Electronic Monitor Water Bottle Holder (Bottle not included) Handlebar Seat Knob Seat Seat Post Frame 3 ASSEMBLY Assembly requires two people. Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Read through all steps before beginning. During assembly,

2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM.........................................................................………. 4 PARTS LIST...................................................................................................... 5 WARRANTY.................................................................................

Slide a Weld Cover (63) onto each of the indicated axles on the Front and Rear Uprights (7, 2). The Weld Covers must be turned so the open sides are facing the Uprights. Lubricate the axles. Slide a Long Riser (3) onto the axles. The Long Riser must be turned as shown. Hold a 3/4" Retainer (57) and a 3/4" Retainer Cap (59) against the end of one of the axles. The teeth on the Retainer must bend toward the Retainer Cap (see the inset drawing). Tap the Retainer and Retainer Cap onto the axle. Tap

Attach an M8 Washer (43) and an 8mm Locknut (36) to each end of the Pivot Shaft. 1 34 56 46 12 43 46 2 20 57 43 40 45 46 3 36 41 36 46 17 10 4 43 36 4 5. The Electronic Monitor (19) requires two OAAO batteries (not included). Alkaline batteries are recommended. Locate the battery compartment on the back of the Monitor. Insert two batteries into the Monitor. Make sure that the negative ends of the batteries (marked O.O) are touching the springs in the Monitor. Close the battery cover. 6. Thread t