ADAPTER PLATE allows the user to move up in 5 lb. weight increments. To attach the 5 lb. plate to the weight stack, carefully rotate the plate so that the cable will slide through the slot, then lower the plate onto the head plate and over the head plate shaft. Part # 6721301 1 Revision: 07/28/97

ADD-ON KIT p v\»\ I ||| [ ASSEMBLY INSTRUCTIONS J Part # 6827301 1 Revision: 3/30/99 PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 6284501 20 HOLE WEIGHT STACK SHAFT 1 3 6198501 WEIGHT STACK LABEL (1-25) 1 2 6382301 WEIGHT PLATE BUSHING 10 CT 1 4 6214501 WEIGHT PLATES 5 • Snap two WEIGHT PLATE BUSHINGS (3) into the top of all five WEIGHT PLATES (6) as shown in FIGURE 1. 2 STEP 2: • Remove the WEIGHT STACK SELECTOR PIN from the WEIGHT STACK as shown in FIGURE

BOLT............................... 2. 3/8X3 IN. BOLT............................... 3. 3/8 IN. WASHER................................ 4. 3/8 IN. LOCK NUT ............................ 5. 2-3/8 IN. CABLE RETAINING CLIP 6. 2-7/8 IN. CABLE RETAINING CLIP 7. 2 IN. SQ PARABODY COVER CAP 8. 3-1/2 X 1 IN. PULLEY....................... NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH RULER: 1/2 I 1/2 1/2 1 1/2 I 1/2 I 1/2 0 I 1 1 I I I.....JL 2 I 3 ■ I

BOLT, one (1) 2-3/8 IN. CABLE RETAINING CLIP, and one (1)3/8 IN. LOCK NUT. - . LOOSELY assemble one (1) 3-1/2 X 1 IN. PULLEY to the middle pulley flat of the 350 BASE using one (1) 3/8 x 2 IN. BOLT, one (1) 2-3/8 IN. CABLE RETAINING CLIP, and one (1) 3/8 IN. LOCK NUT. SECURELY attach the BASE CONNECTION WELDMENT and the 832 to the base of the 350 using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. LOCK NUT S. Following the cable routing diagram, thread the LEG PRESS

PARABÔDY INC. FACTOR 625 D-RING RETRO KIT 607/608 PRODUCT ASSEMBLY INSTRUCTION SHEETS TOOLS REQUIRED FOR ASSEMBLY . RATCHET . 9/16 INCH SOCKET . 7/16 INCH WRENCH . ADJUSTABLE WRENCH REVISION: A If you experience any problem with the assembly of this product, please contact yoiur or your PARABODY Customer Service Representative at: 1-800-328-9714 607/608 FACTOR 625 D RING RETRO KIT ASSEMBLY PARTS LIST HARDWARE/PARTS: ITEM NAME/DESCRIPTION QTY 1. D-RING WLDMNT......................

4 8. D-RING CABLE CLIP ...................................................(3200501)....................................... 4 9. VINYL CAP....................................................................(3201402)....................................... 1 607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS STEP 1: D-RINGTINSTALLATION 1. To assemble the new D-RING to the FACTOR 625, use the following steps: • Remove all the CABLES from the old D-RING. • Loosen, and remove the two (2)

ADD-ON KIT WARNING: Read and follow all directions for each step to insure proper asembly of this product. ASSEMBLY INSTRUCTIONS CLASS H 1 PART # 7016801 Version: 216101 REV. B Revision: 03/23/01 PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 6939201 WEIGHT PLATE 5 3 6978101 WEIGHT STACK LABEL 1 2 7095801 WEIGHT STACK SHAFT 1 4 6382301 WEIGHT PLATE BUSHINGS (10 CT) 1 STEP 1: • Insert two WEIGHT PLATE BUSHINGS (4) into each of the five WEIGHT PLATES (1) as shown

BOLT.......................................... ................................ 1 ‘ 2. 3/8 X 3 IN. BOLT.......................................... ................................ 6 3. 1/2 X 3 IN. BOLT.......................................... ................................ i: -. 4. 3/8 X 1-1/4 IN. BOLT.................................... ................................6- 5. 1/2 IN. WASHER........................................... ................................ 3 6. 3/8 IN. WASHER

BOLT, one (1) 1/2 IN. WASHER, and one (1) 1/2 IN. LOW HEIGHT LOCK NUT. (NOTE: TIGHTEN SWIVEL SLEEVE ENOUGH THAT IT SWIVELS FREELY, YET IT DOESN'T WOBBLE) 10. Insert two (2) 1-3/4 IN. SQ. END CAPS into each end of the ADJUSTABLE SLIDE. 11. Insert the multiple hole end of the ADJUSTABLE SLIDE into the SWIVEL SLEEVE. (NOTE: BE SURE SWIVEL SLEEVE IS IN THE PROPER POSITION, SEE DRAWING) Attach the other end to the ADJUSTABLE SLIDE MOUNT on the BACK PAD, using one (1) 1/2 X 3 IN. BOLT, two (2) 1/2 I

A 1 Revision: 01/21/02 Part # 7241101 • Remove shroud and install cable assembly as shown with components included in kit. Secure all bolts and re-install shroud 2