CBU-10 155271-03 4. Teflon® Sleeve 163518 5. Quartz Sleeve 163509 6. O-rings for Quartz sleeve 163516 7. Plunger Rod w/retainer 163519 8. 3/4” blk cap w/o pr SPECIAL ORDER 9. Spacer Bushing 163517 10. Mounting bracket SPECIAL ORDER 11. UV Lamp 163508 12. Control Module (120v/60Hz) 163506 for use with UV-110-1 Control Module (220v/50Hz) 163507 for use with UV-110-2 13. SW-2 Wrench (not shown) 150295 UV-120 UVBB-120 REPLACEMENT PARTS Part Description: 1. 20” Housing 2. O-ring 3. Gasket for Insert

CARTRIDGE REPLACEMENT (for UVS-110 and UV-110 only) Your cartridge should be replaced when there is a noticeable drop in water flow at the faucet or tap, and/or when unpleasant odors return (approximately every 6-9 months). 1. Turn off water supply to the system. 2. Open faucet to relieve water pressure to the housing. 3. Unscrew housing from cap. If housing sticks or is difficult to open use an Pentek spanner wrench. 4. Remove used cartridge from housing, remove Teflon® sleeve and discard cartr

GENERAL PRECAUTIONS WARNING: Always disconnect the UV from the power source. Follow the procedures provided in this manual. Improper handling can result in death or serious injury. WARNING: Do not look directly at the UV lamp. This can cause retina/eye damage. WARNING: Do not touch the UV bulb. Any fingerprints or dirt will reduce the efficiency of the bulb and may cause it to explode. WARNING: Observe caution when inserting quartz sleeve to prevent breakage and cracking, which may result in inj

If a defect in workmanship and/or material in a product or part covered by the warranty should arise, Pentek, at its sole discretion, will repair or replace the defective product or part (Pentek may consider, in good faith, the customer’s preference). All claimed defective product must: (1) be authorized for return by Pentek with an RGA number (2) include proof of the purchase date of the product or part (3) returned to Pentek prior to the expiration of the warranty date, at the customer’s expen

If carton or any filter components are damaged, notify freight carrier immediately. 2. After inspection, carefully remove filter components from carton — filter tank, gauge, air bleeder. 3. Place the filter in its permanent location on a level slab, preferably concrete poured in a form or on a platform constructed of concrete block or brick. DO NOT use sand to level the filter and pump mounting as it may wash away, leaving the unit out of level. During operation this condition will cause vibra

Installation of a 12 Volt transformer is required when installing the 12 Volt model of this light. The transformer must be located: • at least 10’ from the pool wall, • installed near a grounded, 3-prong, 120V, GFCI protected outlet. If you do not have a GFCI protected outlet, have a qualified electrician install one. Do not use a 3-prong adapter. The adapter voids the grounding of the system. Do not cut the grounding pin. Do not use an extension cord! Purchase a light with a longer cord. 1. Be

Install this equipment in accordance with the instructions provided. Use only with the components and mounting hardware provided. FAILURE TO FOLLOW THESE INSTRUCTIONS AND/OR USE WITH COMPONENTS NOT PROVIDED BY PENTAIR SPA & BATH PRODUCTS AND INTENDED TO BE USED WITH THIS PRODUCT MAY RESULT IN IMPROPER POSITIONING OR FUNCTIONING OF THE COVER AND MAY CAUSE SEVERE PERSONAL INJURY OR DEATH. AWARNING Never use a pool or spa that has a missing or broken cover. USING A POOL OR SPA WITH A MISSING OR B

The result is a filtration and circulation system engineered to provide superior performance, longevity and lifetime value. Key features include: • Tagelus filters include design features that continuously flatten and level the sand inside the tank, a key to more effective and efficient filtration, and longer run times between backwashing. • Easy does it. Tagelus features the handy six-position Hi-Flow™ valve with manual air relief valve and a sight glass to make inspections, routine mainten

A host of design features combine to keep Legend on the move, thoroughly cleaning most pools in just 1 to 3 hours. • Independent booster pump provides optimum cleaning power and unimpeded surface skimming. • Front-wheel drive generates maximum traction on inclined surfaces for total coverage of pool bottom and walls. • 4-wheel design and wide base prevent tipping (common with 3-wheel cleaners) for uninterrupted performance. • Unique debris channel and large intake throat handle leaves, twigs

Powered by a low cost, energy-efficient booster pump, Jet-Vac cleans most pools completely in just 1-3 hours. 1 Independent pumping power and a large 41/2" intake throat allows Jet-Vac to suck up even large debris with ease—in one test it picked up 27 golf balls! With its patented, built-in reverse mode, Jet-Vac moves out of corners and away from obstacles that tend to trap other cleaners. Plus, unlike other cleaners, it continues cleaning, even when in reverse. Just set it and forget it for c