The names Raytheon and RTN are owned by the Raytheon Company. ST40 Compass Instrument - quick reference guide Normal operation SWITCH ON t Compass heading Times out to the Compass heading screen after 5 seconds. o Locked heading Course computer sets auto lock Off course alarm values _Course computer sets auto lock ' Alarm on/off -+o 3 seconds Auto locked heading o -+- o Momentary :i>| alarm level 4+ o -I o i- With Set alarm level screen displayed, press the O and O

In this case, proceed to 'Cutting the bracket'. • There are two alternative slots for the bracket in the back cover of the wheel drive (Slot 1 and Slot 2). • Locate the motor tube where: • a 55 mm (21/e in) hole can be cut in the bulkhead/pedestal (if required) • the seal and ring can be secured around the motor tube • there is sufficient space behind the mounting location to allow at least 10 mm (0.4 in) clearance around the motor (see diagram below) CAUTION: Mount the drive so the motor

Initiates the Dual-Watch monitor mode. Pressing FUNC + MON/TRI starts the Tri-Watch monitor mode. Changes the volume of the handset. Alternately inputs the characters 2, A, B, and C. Pressing FUNC + 2/SCAN toggles ON and OFF the Scan mode. TRI VOL SCAN POWER Switches to DSC Individual Ships Call mode for initiating ship-to-ship or ship-to-shore calls using a specific MMSI number. Switches to the All Ships Call mode for Safety and Urgency transmissions. MEM Alternately inputs a 1 or a space chara

AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. DIRECTV is an official trademark of DIRECTV Inc., a unit of GM Hughes Electronics. DISHTM Network is an official trademark of EchoStar Communications Corporation. ExpressVu is a property of Bell ExpressVu, a wholly owned subsidiary of Bell Satellite Services

Set to a level appropriate for your needs SmartPilot® ST7002 Controller r Use? or ▲ to adjust response level. Press disp to return to previous mode. To Adjust Lighting Level 1 sec Use disp to adjust lighting level. Wait 10 sec to return to previous mode. \j3uick Start GuideJ Display Layout disp Press to display data pages Press for 1 second for lamp control Press for 3 seconds for power off resp Press to display response level track When the Autopilot is activated, press to folow

Press again to accept the new course mode Press to select Wind Vane mode res m Press to resume previous course Press to adjust calibration, response and gain course change keys Port 1° Starboard 1° Port 10° Starboard 10° auto Press to activate the Autopilot standby + auto Press for Wind Vane mode standby Press for Manual Control L To activate the Autopilot For Manual Control 115176 To change the Autopilot Heading To follow a Route set on a Chartplotter

Format PAL 752 x 582 pixels NTSC 768 x 494 pixels Video connector Imager 1/ 3 Sony Super HAD CCD (Super Hi resolution) Horizontal resolution 550 TVL Scanning system PAL 625 lines NTSC 525 lines 2: 1 interlaced Red +12 V Video output Composite 75 Ohms Black - 0 V D8537_1 Infra red 14 IR LEDs If you do not have a breaker in the power circuit, an in- line 0.5 A quick blow fuse should be fitted to the positive (red) lead of the cable. LED spectrum 30 degrees for 15m Maintenance and Troubleshooting M

Its accuracy can be affected by many factors, including equipment failure or defects, environmental conditions and incorrect handling or use. It is the user’s responsibility to exercise common prudence and navigational judgement. This device should not be relied upon as a substitute for such prudence and judgement. CAUTION: Do not connect/disconnect the GPS Antenna from the display unit whilst power is applied. Such action could cause irreparable damage. WAAS Satellite Differential GPS WAAS prov

Trackpad Used to control the on-screen cursor and to scroll through menu items. Press the corresponding edge of the trackpad to move the cursor horizontally, vertically or diagonally. Press and hold to move rapidly over larger distances. CANCEL Press to cancel the selected on-screen option when editing data; also used to return to the previous soft key set or menu. MENU Press to access the set up menus. ACTIVE When multiple windows are open: - Press to select required window. - Press and hold to

Raychart 420/ 420D Chartplotter Owner’s Handbook Document number: 81162_2 Date: January 2000 RayChart 420 and 420D Chartplotter Owner’s Handbook SAFETY NOTICES 1. HIGH VOLTAGE. The display unit contains high voltages. Adjustments require specialised service procedures and tools only available to qualified service technicians – there are no user serviceable parts or adjustments. The operator should never remove the display unit cover or attempt to service the equipment. 2. NAVIGATION AID. This de