The filter cycle begins six (6) minutes after the spa is energized. The second filter cycle begins 12 hours later. Filter duration is programmable for 2, 4, 6, 8 hours of for continuous filtration (indicated by FILC). The default filter time is 2 hours. To program, press “Temp” then “Jets”. Press “Temp” to adjust. Press “Jets” to exit programming. The default filter time is 2 hours. Troubleshooting No power to spa: 1. Check proper connection of to pack 2. Check fuse in pack. 3. Must have very go

This type of chemical can be added in quantities of 0.5 ounce per 500 gallons of spa water. Check the chlorine level at least seven hours or more after adding to determine the full effect of the added chemical. Liquid chlorine is not recommended. ORGANIC POLYMERS - are used in various forms. These chemicals clear up cloudy or dirty water appearance and prevent calcium deposits on the inside spa finish, plumbing and heating equipment. Use as recommended by the manufacturer. METAL GON - or its equ

OWNER’S MANUAL Patriot ™ 3204 Point Township Drive (Rte 11) • P.O. Box 108 Northumberland, PA 17857 1-800-STRONG-9 1-800-787-6649 12/20/06 Table of Contents Introduction ................................................................................................................................. 1 Health Safety.............................................................................................................................. 2 Installation -Spa placement ............................

Freeze Protection If the temperature sensors detect a drop to below 44.F/6.7.C within the heater, the pump will automatically activate to provide freeze protection. The equipment stays on until 4 minutes after the sensors detect that the spa temperature has risen to 45.F/7.2.C or higher. 9 Spa Maintenance The maintenance and care of your spa is simple and easy to carry out, and if performed regularly as scheduled, problems will be minimal. It is important that the following procedures be read th

WINTERIZING Before draining, power must be turned off at the GFCI circuit breaker. Attach a garden hose to the faucet and open it. Water will start to drain. You can use the water to water the garden. You can also siphon the water from the spa. The drain faucet will not remove all the water. You may have to remove a small amount of water by hand, using a towel. You must also use a wet-vac to remove the water from the lines by suction and/or blowing. Water left in the line and jets might freeze a

Long exposure at higher temperature can result in dizziness and/or hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98°F (36.7°C). The symptoms of hyperthermia include dizziness, fainting, drowsiness or lethargy. The affects of hyperthermia include: • Unawareness of impending hazard • Failure to perceive heat • Failure to recognize the need to exit the spa • Physical inability to exit the spa • Fetal

A location should be selected to compliment your lifestyle, the view from your house and the ability to supervise the spa. Position the spa in relation to the surroundings of trees, sunlight exposure, wind, bathroom location, landscaping and evening lighting. The spa with water is very heavy, if the spa is placed on flooring or decking, be sure the structure is strong enough to support the weight. The necessary support should be at least 75 pounds per square foot. Install your spa, in a way that

(repair or replacement) Spa Surface: 3 years Strong Spas warrants the original retail purchaser the surface integrity of the spa against blistering or delaminating as a result of defects in material or workmanship for a period of 3 years. (repair or replacement) Plumbing: 3 years Strong Spas warrants the original retail purchaser the integrity of the spas plumbing against leaks as a result of defects in material or workmanship for a period of 3 years. (parts and labor)3 Equipment: 2 years Strong

Solution: If the problem persists, contact your dealer or service organization. 8 Troubleshooting continued from previous page Problem: A significant difference between temperature sensors has been detected. This could indicate a flow problem. Solution: Check water level in spa. Refill if necessary. If water level is okay, make sure the pumps have been primed. If problem persists, contact your dealer or service organization. Problem: Persistent low flow problems. (Displays on the fifth occurrenc

OWNER’S MANUAL Liberty ™ 3204 Point Township Drive (Rte 11) • P.O. Box 108 Northumberland, PA 17857 1-800-STRONG-9 1-800-787-6649 12/20/06 Table of Contents Introduction ................................................................................................................................. 1 Health Safety.............................................................................................................................. 2 Installation -Spa placement ............................