16 WARRANTY WARRANTY LIMITATIONS WARRANTY TERMS The following is NOT covered under TUNN (Effective April 1st. 2008) warranty program: These terms supersede all prior published warranty terms 1. Product owned by anyone other than the TUNN products are warrantied against original purchaser from an authorized TUNN dealer. defects in materials and workmanship for (The warranty is NOT transferable and a period of One (1) Year from the original will not apply to products purchased from date of purchas

The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 50Hz to 250

Use Solder or a clamp ring to connect the ground wire. Pre-drill the prepped chassis to bolt the ground ring terminal with nut, bolt and lock washers. Insulate metal and connector with paint or silicon to prevent rust and oxidation. Silicon also works great to prevent nuts and bolts from working loose in a harsh environment of an automobile. Upon completion of the ground connection, grab wire or connector and confirm that it is a solid connection. To prevent engine noise, it is recommended to gr

Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation. Features • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' Technology MOSFET PWM Power Supply. • Bridgeable & TRI-Mode Operation. • Continuously Variable 12dB/Octave High Pass & 12dB /Octave Low Pass Crossover. • Subwoofer Variable Crossover for Deep Bass Control. • Enhanced Bass Boost +12dB @ 45Hz. • Silver Plated

Check all grounds , battery voltage, and RCA cables Ticking noise on audio with engine running Amplifier is picking up radiated spark noise Check RCA audio cable; Install an in-line noise filter on the head unit's power wire. Check spark plug wires. 14 SPECIFICATI SPECIFICATISPECIFICATION ONON Output Power Rating RMS T-270 T-2100 T-2130 Channel 2CH 2CH 2CH Total Max Power 900 Watts 1200 Watts 1500 Watts 4 Ohm at 14.4V 0.3%THD ( RMS ) 4 Ohm at 14.4V ( MAX ) 2 Ohm at 14.4V 0.3%THD ( RMS ) 2 Ohm at

• NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at the amplifier may cause damage to the amplifier and will void your warranty. • Do not run wiring underneath or outside the car since exposure to the elements may cause the insulation to dete

Check spark plug wires. 14 SPECIFICATION AMPLIFIER G2-600 G2-800 G2-1200 4 OHMS @ 0.05% THD 100W x 2 150W x 2 225W x 2 4 OHMS Bridged 0.5% THD 200W x 1 300W x 1 450W x 1 MAXIMUM OUTPUT POWER 600 Watts 800 Watts 1200 Watts BASS LEVEL REMOTE CONTROL(16.4Ft) YES (OPTIONAL) YES (OPTIONAL) YES (OPTIONAL) LOW PASS FILTER 50Hz-250Hz (VARIABLE) 50Hz-250Hz (VARIABLE) 50Hz-250Hz (VARIABLE) HIGH PASS FILTER 80Hz-1.2kHz (VARIABLE) 80Hz-1.2kHz (VARIABLE) 80Hz-1.2kHz (VARIABLE) FREQUENCY RESPONSE (-1dB) 10Hz-

It is important to have the amplifier turn off with the radio or key. If the amplifier remains on, the result will most 2CHANNEL SYSTEM WIRING DIAGRAM LINE INPUT GAIN BASS L.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz 80Hz 1.2KHz CROSSOVER CH1 CH2 REMOTE FLAT L.P.F H.P.F +12V REM GND AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT FIG.2 5 4CHANNEL SYSTEM WIRING DIAGRAM LINE INPUT LINE INPUTGAIN GAINBASS BASSFREQUENCY FREQUENCY 6V 0.2V 0dB 12dB 50Hz 500Hz FLAT L.P.F H.P.F FLAT L.P.FH.P.F CH1 CH2 CH3 C

advisable to prevent straining or breakage. to normal. qualified mechanic. with each other. Speaker wire should be 18 gauge or larger. accessory. If the amplifier does not turn off the battery will die. INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier

The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 50Hz to 250