The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 50Hz to 250

16 WARRANTY applied to products. (Interfire Audio will not be WARRANTY LIMITATIONS The following is NOT covered under Interfire Audio's warranty program: manual lightning, etc.) Custom finishes) Product with defaced, altered or removed serial numbers (no valid, legible serial No. = no warranty). or missing magnets. 1. 3. 4. 5. 6. 7. 8. WARRANTY TERMS (Effective January 01, 2010) These terms supersede all prior published warranty terms Interfire Audio products are warrantied against defects in ma

16 WARRANTY WARRANTY LIMITATIONS WARRANTY TERMS The following is NOT covered under TUNN (Effective April 1st. 2008) warranty program: These terms supersede all prior published warranty terms 1. Product owned by anyone other than the TUNN products are warrantied against original purchaser from an authorized TUNN dealer. defects in materials and workmanship for (The warranty is NOT transferable and a period of One (1) Year from the original will not apply to products purchased from date of purchas

Because the Class "D" amplifier is capable of drawing in excess of 90 amperes,4 gauge wire is recommended for lengths up to twenty feet. if a longer length is needed , a larger gauge wire may be necessary. POWER Amplifier power wire should be wired directly to the battery using the wire requirements listed above. Start at the amplifier and run the power wire through the vehicle to the battery. The use of grommets is recommended when passing the power wire through any metal wall. Avoid sharp corn

advisable to prevent straining or breakage. to normal. qualified mechanic. with each other. Speaker wire should be 18 gauge or larger. accessory. If the amplifier does not turn off the battery will die. INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier

Check spark plug wires. 14 SPECIFICATION AMPLIFIER G2-600 G2-800 G2-1200 4 OHMS @ 0.05% THD 100W x 2 150W x 2 225W x 2 4 OHMS Bridged 0.5% THD 200W x 1 300W x 1 450W x 1 MAXIMUM OUTPUT POWER 600 Watts 800 Watts 1200 Watts BASS LEVEL REMOTE CONTROL(16.4Ft) YES (OPTIONAL) YES (OPTIONAL) YES (OPTIONAL) LOW PASS FILTER 50Hz-250Hz (VARIABLE) 50Hz-250Hz (VARIABLE) 50Hz-250Hz (VARIABLE) HIGH PASS FILTER 80Hz-1.2kHz (VARIABLE) 80Hz-1.2kHz (VARIABLE) 80Hz-1.2kHz (VARIABLE) FREQUENCY RESPONSE (-1dB) 10Hz-

Check all grounds , battery voltage, and RCA cables Ticking noise on audio with engine running Amplifier is picking up radiated spark noise Check RCA audio cable; Install an in-line noise filter on the head unit's power wire. Check spark plug wires. 14 SPECIFICATI SPECIFICATISPECIFICATION ONON Output Power Rating RMS T-270 T-2100 T-2130 Channel 2CH 2CH 2CH Total Max Power 900 Watts 1200 Watts 1500 Watts 4 Ohm at 14.4V 0.3%THD ( RMS ) 4 Ohm at 14.4V ( MAX ) 2 Ohm at 14.4V 0.3%THD ( RMS ) 2 Ohm at

Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation. Features • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' Technology MOSFET PWM Power Supply. • Bridgeable & TRI-Mode Operation. • Continuously Variable 12dB/Octave High Pass & 12dB /Octave Low Pass Crossover. • Subwoofer Variable Crossover for Deep Bass Control. • Enhanced Bass Boost +12dB @ 45Hz. • Silver Plated

The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 50Hz to 250

Master Amplifier Slave Amplifier Recommend : Competition Only MONO BRIDGED SPEAKER WIRING FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ MONO BRIDGED (OPTION) FOUR AMPLIFIER/ ONE SUBWOOFER (DUAL VOICE COIL)CONFIGURATION 6 Master Amplifier