45-03621 45-03622 42" ROUGH CUT TRAILMOWER IMPORTANT: BATTERY REQUIRED!! The battery is NOT included with the deck but must be purchased separately. A 12 volt lawn tractor battery with 260/300 cold cranking amps and dimensions of 6-1/8"H x 7-5/8"L x 5-1/8"W is recommended to operate the machine. CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts FORM NO. 49463 (REV. 10/01/08) PRINTED IN USA 2 T

1. Turn the spreader upside down as shown in figure 1. FIGURE 2 6. Tighten the nuts and bolts fastening the hitch braces to the hopper frame and the hitch tube, then tighten the middle lock nut fastening the hitch tube to the crossover tube. DO NOT COLLAPSE TUBES WHEN TIGHTENING. 7. Assemble a spacer (P), a 3/4" flat washer (K), a wheel (air valve facing out) and another 3/4" flat washer (K) onto the end of the axle that has only the small hole. See figure 3. 8. Install a 1/8" x 1-1/2" cotter pi

Assemble a door latch at each end of the cross brace using a 5/16" x 3/4" hex bolt, a nylon washer and a 5/16" Nylock hex nut. Place the nylon washer between the door latch and cross brace. Tighten so that latch is snug but will still rotate. See figure 13. 20. Place a side panel on top of the cart bed flange, inside the lip of the front panel. Fasten the side panel to the front panel using three 1/4" x 5/8" hex bolts and 1/4" Nylock hex nuts. Fasten the side panel to the cart bed flange using t

45-0350, 45-0351 18 10 9 REPAIR parts for CART MoDEL No's. 45-0350, 45-0351 REF. NO. PART NO. DESCRIPTION 45-0350 45-0351 1 25112 Cart Body 2 2 2 23502 Tailgate 1 1 3 62458 Tailgate Reinforcement Bracket 1 1 4 23548 Tailgate Guide 5 23492 Front Panel 1 1 6 25106 Wheel Support 1 1 7 24497 Latch Stand Bracket 1 1 8 24498 Latch Lock Lever 1 1 9 23014 Hitch Bracket 1 1 10 25114 Draw Bar Tongue 1 1 11 25107 Axle, 1" Dia. 1 1 12 23484 Front Corner Cap 2 2 13 43594 Wheel, 16/6.5" x

47927 (Rev. 9/11/08) 2 REPAIR PARTS FOR 45-0365 - PUSH SPIKE AERATOR REF QTY PART NO DESCRIPTION REF qty PART NO DESCRIPTION 1 1 24719 Frame Tray 11 2 46497 Spacer, 1.2" Long 2 5 24332 Spike Disk 11A 4 23368 Spacer, .75" Long 3 1 24720 Axle 12 4 R19212113 Washer 4 2 24369 Endplate 13 4 47141M Wingnut, M6 5 2 47925 Straight Handle Tube 14 4 45039M Carriage Bolt, M6 x 40 6 2 47926 Foot Tube 15 8 43182M Hex Bolt, M8 x 20 7 1 47924 Upper Handle Tube 16 8 47810M Nylock Nut, M8 8 7 741-0249

45-0414 45-0415 125 LB. TOW BROADCAST SPREADER • Safety • Assembly • Operation • Maintenance • Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully the fastest way to purchase parts FORM NO. 40454 Rev. (5/15/09) PRINTED IN USA 2 RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • Read the towing vehicle owners manual and to

Lubrique los cojinetes de las ruedas en cada temporada. Retire la tapa del cubo y aplique unas pocas gotas de aceite liviano. 6. (Figura 25) Cada dos anos retire las ruedas y limpie los engranajes que se encuentran dentro de la carcaza de la rueda. Despues de limpiarlos, lubriquelos con una capa pareja de grasa liviana. Para retirar la rueda, saque la tapa del cubo y retire la contratuerca o tuerca de cierre y la arandela plana. PRECAUCION: .Nunca amarre la cuerda de la tolva a ninguna parte de

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clu