Other customers should contact their place of purchase. Seagate offers comprehensive customer support for all Seagate drives. These services are available worldwide. Location Phone number FAX number Asia Pacific and Australia 65-485-3595 65-488-7503 Europe, Middle East, and Africa 31-2031-67300 31-2065-34320 Japan 81-3-5462-2904 81-3-5462-2979 USA 1-800-468-3472 405-949-6740 Other Americas (Brazil, Canada, Mexico) 405-949-6706 405-949-6738 Cheetah 18 Installation Guide, Rev. A Location Phone num

Preparing the drive using DiscWizard Installing a single drive If you are installing a single drive, we recommend using DiscWizard to automatically partition and format your drive. DiscWizard software is available at and is free. During the download, the Diskette Creator creates a portable bootable diskette. To run DiscWizard: 1. Insert your bootable DiscWizard diskette and follow the instructions. DiscWizard will guide you through the installation process. 2. Boot your computer from the Windows

If using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive and the grey connector to the slave. Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable. 2. Secure the drive using four 6-32 UNC mounting screws in either the side- mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and

Wenn Sie das Systemgehause nicht an die HDA/PCB- Erdung anschlie.en wollen, mussen Sie das Laufwerk auf nichtleitende Weise (galvanisch isoliert) im Host-Sys Barracuda 4LP Installation Guide, Rev. B tem einbauen. Die daraus u.U. resultierende verstarkte elektromagnetische Strahlung fallt in den Zustandigkeitsbereich des Systemdesigners. 5. Replace the host system’s cover. 5. Setzen Sie das Gehauseoberteil des Host-Systems wieder auf. Barracuda 4LP Installation Guide, Rev. B [4] A F D E L [1] [3]

Bits 7, 6, 5, 3, 2, 1, and 0 are changeable, because those bits are all ones. Bit 4 is not changeable. Though the drive always reports non-zero values in bytes 00 and 01, those particular bytes are never changeable. The Changeable values list can only be changed by downloading new firmware into the flash EPROM. On standard OEM drives the Saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping. When a drive is powered up

To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at for more information. Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only fac

29 N drives section ......................................................................... 36 W/WD drives section .................................................................40 WC/DC drives section................................................................45 ©1997 Seagate Technology, Inc. All rights reserved Publication Number: 77767492, Rev. B January 1997 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology, Inc. Barracuda, SeaFAX, SeaF

The top example in Figure 2 shows an internal hard disc at one end of the SCSI bus with the SCSI controller at the other end (both are terminated). The bottom example shows two additional SCSI devices connected externally—this means the SCSI controller is no longer on the end of the SCSI chain and should not be terminated. Note. Some controllers prefer to remain terminated even if they are in the middle of the chain. Also, some controllers treat the internal and external chains as separate logic

Compliance of this drive, as a system component, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc.). Sicherheitsanleitung 1. Das Gerrat ist ein Einbaugerat, das fur eine maximale Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks werden 4 Schrauben 6-32 UNC-2A benotigt. Bei seitlicher Befestigung darf die maximale Lange der Schrauben im

• Cable select: Computers that use cable select to determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interOptions jumper block face bus. To enable cable select, set a jumper on pins 5 and 6. • Alternate capacity jumper: Drives with a 40-Gbyte capacity or greater are limited to 32 Gbytes. Use this jumper only if you have a legacy system with a BIOS that does not support large capacity disc drives. When using the alternate capacity jumper, • Manager software is