Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  

Anritsu S251C

Descargado: 33Tamaño del archivo: 951 kb    Fabricar: Anritsu  
Categoría: estéreo

A complete open, short, and load calibration must be performed before calibration can be turned on. Valid distance to fault plots require a non-zero frequency span. Distance-to-fault measurements cannot be performed with CAL OFF. Attempting to print a display with no printer selected. Select a printer, then retry. Attempting to perform a Power Monitor zero adjust function with no RF detector connected to the Site Master. Attempting to perform a Power Monitor zero adjust function with an input of

Anritsu 681XXC

Descargado: 1Tamaño del archivo: 2 mb    Fabricar: Anritsu  
Categoría: Electricidad

Anritsu’s obligation covers repairing or replacing products which prove to be defective during the warranty period. Buyers shall prepay transportation charges for equipment returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for consequential damages. LIMITATION OF WARRANTY The foregoing warranty does not apply to Anritsu connectors that have failed due to normal wear. Also, the warranty does not apply to defects resulting from imprope

Anritsu S331C

Descargado: 11Tamaño del archivo: 657 kb    Fabricar: Anritsu  
Categoría: estéreo

Channel Power measurements are used to validate transmitter performance, verify compliance with FCC regulations, and keep overall system interference at a minimum. Out-of-specification power measurements indicate system faults in the power amplifier or in-filter circuits. Channel Power Measurement with the Site Master The Site Master can be used to measure CDMA signals in terms of channel power. It is necessary to use precise and specific settings to accurately measure the CDMA signal because th

Anritsu Site Master S332D

Descargado: 161Tamaño del archivo: 566 kb    Fabricar: Anritsu  
Categoría: Equipo de red

Send a 0 (zero) following the command to set the channel power measurement in the current setup. Send a 1 (one) to set the channel power associated with the trace that was most recently uploaded by command #36, Upload Sweep Trace. If Option 6 is installed and the frequency converter module is attached, the frequencies should be scaled by the scale factor of the module. If the module is not attached, frequencies are sent in Hz. Use Control Word A203 to determine whether a module is attached and t

Anritsu S113C

Descargado: 0Tamaño del archivo: 657 kb    Fabricar: Anritsu  
Categoría: estéreo

Spectrum Analyzer Mode Soft Key Labels (continued) MODE=POWER MONITOR: SOFTKEYS: UNITS REL OFFSET ZERO Figure 2-6. Power Monitor Mode Soft Key Labels Chapter 2 Functions and Operations FREQ/DIST Frequency Menu Distance Menu Distance Sub-Menu Displays the frequency and distance menu depending on the measurement mode. Provides for setting sweep frequency end points when FREQ mode is selected. Selected frequency values may be changed using the keypad or Up/Down arrow key. • F1 — Opens the F1 parame

Anritsu S114C

Descargado: 5Tamaño del archivo: 657 kb    Fabricar: Anritsu  
Categoría: estéreo

Site Master S332C ON/OFF KEY Figure 3-1. Site Master On/Off Key Chapter 3 Getting Started Select the Frequency or Distance Regardless of the calibration method used, the frequency range for the desired measurements must be set before calibrating the Site Master. The following procedure selects the frequency range for the calibration. Step 1. Press the FREQ/DIST key. Step 2. Press the F1 soft key. Step 3. Enter the desired start frequency using the key pad or the Up/Down arrow key. Step 4. Press

Anritsu CMA 5000 - UTA

Descargado: 21Tamaño del archivo: 1 mb    Fabricar: Anritsu  
Categoría: Lavavajillas

STM-64 and OC-192 are widely deployed in today’s networks. While great care is devoted to warrant a very high quality of transport, in the real world of day- to-day installation, commissioning and maintenance activities things are not always running smooth. To this effect, several important tests are always carried out in order to assess the good behaviour of these networks before turn-up. Similarly, when the network has been turned on, it is paramount to keep monitoring the network health at ph

Anritsu Site Master S331D

Descargado: 20Tamaño del archivo: 566 kb    Fabricar: Anritsu  
Categoría: Equipo de red

peak 01b = RMS avg 10b = neg. peak 11b = sampling mode) bits 3-4 : Amplitude Units (Log) -(00b = dBm 01b = dBV 10b = dBmV 11b = dBuV) (Linear) – 00b = Watts 01b = Volts bit 5 : Channel Power On/Off bit 6 : Adjacent Channel Power On/Off bit 7 : Units Type (0b = Log 1b = Linear) 295) Status Byte 4170 (0b = Off/Beep if data is BELOW line, 1b = On/Beep if data is ABOVE line) (LSB) bit 0 : Limit Type (0b = Single, 1b = Multiple) bit 1 : Not Used bit 2 : Single Limit On/Off bit 3 : Single Limit Beep L

Anritsu MT8852A

Descargado: 0Tamaño del archivo: 12 kb    Fabricar: Anritsu  
Categoría: Auriculares inalámbricos y otros accesorios

Anritsu S332C

Descargado: 54Tamaño del archivo: 657 kb    Fabricar: Anritsu  
Categoría: estéreo

Buyers shall prepay transportation charges for equipment returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for consequential damages. LIMITATION OF WARRANTY The foregoing warranty does not apply to Anritsu connectors that have failed due to normal wear. Also, the warranty does not apply to defects resulting from improper or inadequate maintenance by the Buyer, unauthorized modification or misuse, or operation outside the environmenta





Categoría