Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this product was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended. Turn off the Tool and unplug the 6. Power Cord Plug from its electrical outlet before changing accessories or performing inspection, maintenance, or cleani

Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.) To AttachThe Motor Assembly: 1. Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjust

For technical questions and replacement parts, please call 1-800-444-3353 Specifications Air Inlet 1/4 ”-18 NPT Recommended Air Pressure 60 -100 PSI, 100 PSI Max. Magazine Capacity 100 Nails or 80 Staples Safety Feature Single Sequential Safety Trip Mechanism Nail Size .039-.042” Shank (18 Gauge), 5/8 ” -11/ 4 ” L Staple Size 1/4 ” Crown, .039-.042” Shank (18 Gauge), 1/2 ” -11/ 4 ” L Accessories Oil Dropper, 2 Wrenches, 1 Coupler Plug Save This Manual You will need the manual for the safety warn

Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. WEAR PROPER APPAREL. Do not 10. wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. ALWAYS USE SAFETY GLASSES. 11. Also use face or dust mask if cutting operation is dust

7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. REQUIRED MINIMUM EXTENSION CORD GAUGE - 110 VOLT NAMEPLATE AMPERES (At Full Load) EXTENSION CORD LENGTH 0-25 FT. 25-50 FT. 50-100 FT. 100-150 FT. 618 16 14 12 8 16 16 12 10 10 16 14 12 1012 16 14 10 814 14 12 10 816 14 1

Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibr

o implicitas relacionadas con el buen estado o posible uso del producto por parte del consumidor, no podran ser excluidas o renunciadas en forma alguna. Pronta Disposicion. John Deere se compromete a resolver los casos de los productos bajo garantia en forma diligente de acuerdo a lo estipulado en esta garantia limitada. En el caso de que su producto tenga algun defecto y que este cubierto dentro de los limites de esta garantia, dirijase por escrito o llame al distribuidor autorizado donde compr

Plan a safe direction for runoff to flow while the job is being performed, and plan on working your way in that direction. You will have a clearer idea of the time involved to clean the area after doing a test run, as explained on page 15, #3. 5. PREPARE THE CLEANING AREA. Clear the cleaning area of all objects that are not being cleaned. If any water prone or delicate items cannot be moved, protect or move them. If detergent is to be used, cover or remove any plants or animals that may be damag

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 Specifications Item Description Operating Pressure 160 PSI (maximum) Air Inlet and Outlet Size Inlet: 1/2" NPT Outlet: 1/4" NPT Features Replacable air filter element Overall Dimensions 11-3/4" Tall x 3-7/8" DIA. x 8-3/4"Deep Weight 5-1/2 lbs. Fil

15. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 16. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in. 17. Stay alert. Watch wh