Todos los derechos reservados. Este documento esta sujeto a cambios sin aviso previo. 1620 Hawkins Ave., Sanford, NC 27330 • (800) 831-7133 • (919) 566-8000 10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 831-7133 • (805) 553-5000 Marcas de comercio y Descargos de Responsabilidad: PentairWaterPoolandSpa™ y Lil Shark™ son marcas de comercio de Pentair Water Pool and Spa, Inc. Otras marcas de comercio y nombres comerciales pueden ser usados en este documento para referirse a las entidades

This manual supplies information for the installation, operation, and servicing of the appliance. It is strongly recommended that this manual be reviewed completely before proceeding with an installation. Its use will reduce service calls and chance of injury and will lengthen product life. FILTERPUMP AUX1 AUX2 HIGH SPEED LOW SPEED BOOSTER PUMP If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. – Do

F. Before operating the appliance for the first time or after it has been off for an extended time, perform the following checklist: 1. Remove debris or other articles from inside the heater and the area around the heater and its exhaust vent. Make sure the ventilation openings are clear of debris or obstruction. For installations in an enclosed space, make sure openings for combustion and ventilation air are unobstructed. 2. Keep heater area clear and free from combustibles, flammable liquids a

FIGURE 13: U.S. minimum Exhaust Vent clearances. Local codes may differ - consult local code officials. 1' Min. 4' Min.4' Min. 4' Min. 4' Min. 3' Minimum clearance if Vent Termination Termination Gas Meter Metal Vent Body 8. Fire Hazard. Do not run the heater vent . Table 6: Maximum Vent Length 4” Special Gas Vent (Vertical or Horizontal)* No. of 90° Elbows Maximum Length in Feet (M) 0 25 Ft. (7.6M) 1 20 Ft. (6.1M) 2 15 Ft. (4.6M) 3 10 Ft. (3.1M) * Minimum vent length is one foot (.34M), or in a

Electrical power circuits to the pool heater must follow local codes and National Electrical Code or Canadian Electrical Code (as applicable). All wiring between the heater and devices not attached to it, or between separate devices which are field installed and located, shall conform to the specifications of Type T wire (35°C rise). All line voltage wiring shall be enclosed in approved flexible conduit, and shall be securely attached to the field wiring box located inside the jacket. The condui

Orient the heater so that the vent pipe does not interfere with adjustment of the operating controls. The operating control panel located on top of the jacket can be rotated for convenient access to the control panel. Table 1: Corrosive Vapors and Possible Causes Area Likely Contaminants Chlorinated swimming pools and spas Pool or spa cleaning chemicals. Acids, such as hydrochloric or muriatic acid New construction and Glues and cements, remodeling areas construction adhesives, paints, varnishes

NOTICE: When starting the heater for the swimming season with a water temperature below 50°F (10°C), the heater may be used to heat the water; however, make sure that the heater operates continuously until the water temperature reaches the heater’s minimum setting of 65°F (18°C). DO NOT operate this unit outdoors at temperatures below 40°F (4°C). During cold weather, if there is no danger of freezing, operate the filter pump continuously even if the heater is not operating. If air temperatures a

YES 28 Diagnostic LED’s: SFS Replace Heater Membrane Pad Assembly, reset power to Heater and retry. Heater should fire. A) Is the Stack Flue Switch or Sensor correctly connected to the wiring harness? B) Is the Membrane Pad connected to the correct pins on the Control Board? (See Page 36) Check the J3 and J6 connectors for corrosion on the male pins. Corrosion found? Clean pins Reset power to Heater and retry. Heater should fire. Verify whether you have a Stack Flue Sensor or a Stack Flue Switch

Sta-Rite Pool/Spa Group U.S. PATENT NO. 5190651 (Other patents pending) This manual should be furnished to the end user of this filter; its use will reduce service calls and chance of in- jury and will lengthen filter life. 2160 1295 OUTLETOUTLET RELEASERELEASE 2160 1295 OUTLETOUTLET RELEASERELEASE 293 Wright Street, Delavan, WI 53115 North America: 800-752-0183, FAX 800-582-2217 International: 262-728-5551, FAX: 262-728-4461, TELEX: ITT 4970245 Union City, TN • Delavan, WI • Mississauga, Ont. •

Live steam hazard. If the Burner and the Pump stop at the same time, wait at least 15 minutes before starting the filter pump to avoid severe damage to the heater. PRESSURE RELIEF VALVE Canadian code requires and some U.S. local codes may require installation of a pressure relief valve. Purchase separately and install a 3/4” pressure relief valve complying with the ANSI/ASME Boiler and Pressure Vessel Code, having a capacity equal to the Btu/hr rating of the heater. The relief pressure of the va