(R) 81221001 PEDAL/CRANK ASSY. (L) 81222011 PEDAL ONLY (R) 81221011 PEDAL ONLY (L) 81226001 PEDAL STRAP (R) 81227001 PEDAL STRAP (L) 81037001 DRIVE SEAL STD 81038001 DRIVE SEAL I - SERIES 81181001 SPINE 81080001 SPROCKET SHAFT 53170020 SET SCREW 81236001 PEDAL ADJ ASSY INCLUDES: 81240001 PLASTIC HANDLE 81230001 PIN 8031201 SCREW 81242001 SPRING ALLEN WRENCH 81202001 CHAIN ASSY V2 8050111 NUT 81090001 DRUM SHAFT 81190001 STANDARD FIN 81193001 ST FIN 81192001 ST TURBO FIN 81050001 OUTHAU

This will allow you to hook the track edge and pry out from under the lip. Be very carefull not to catch the lip and chip it. (A chipped lip will not hold the Luff track as well but does happen from time to time and may be no problem at alt.) Pry the corner away from the Comptip groove. Once again, Be carful not to chip the lip. Slide the screw driver deeper to hold the track away from the groove. Place the second screwdriver about 6 inches farther down the track and repeat the process. Repeat

Be sure to follow the applicable instructions. Every Wave Mast Float comes with the mounting bracket already installed to the float. All that remains to be done is to attach the mast float by following the proper installation to mast head instruction. 1. Hobie 14 with Comp Tip Mast Head. This mast uses the same mast head as the Hobie Wave. All that needs to be done is to remove the two clevis pins holding the two sheaves in place and replace them with the 2 each 10-32x1 1/2" machine screws. Rem

Locate the left and right rudder assemblies. The left one has a red dot and the right one a green dot. The tiller arms should have a slight bow towards the centerline of the boat. INSTALLING THE SAIL BATTENS Unfold the sail and lay it out on the trampoline. There will be a small bundle of thin lines tied to the top of the sail. These are the batten tension lines. Tie the batten tension lines to one of the small grommets at the end of each batten pocket as diagramed in figure 28 (one to each batt

This may not be a suitable replacement for the original rivet due to hole wear. ANCHoR PiN 20100000 NUT 8050321 10092000 10091000 H18 tRAmpOlInE CoMPLETE TRAMPoLiNE 6097XXXX (XXXX = Color / See parts list for available options) (does not include lace line) CENTER LACiNg LiNE RH014WHT X 19' H18 FWd CROssBAR 8031031 CUSToM 61020001 LoCK WASHER 8080581 CHANNEL 61110000 boLT 8040561 H18 REAR CROssBAR REAR CRoSSbAR - EXTRUSioN oNLy bLACK 60191211 boLT 8040501 NUT 8050521 CHANNEL mAst stEp AssY. SCREW

Note that the holes in the bracket are slightly oversized to allow the bracket to rotate to allow the holes to align with the holes in the support leg. Be sure the right angle side of the bracket faces up. The angled side goes down. Complete wing installation before tightening these bolts to allow for any variance in fit. 2) Install the tension leg assembly (the telescoping tube assembly) and the support leg (larger 2” tube) into the end cap casting as shown using the 3/8x3.5” bolt. Put some su

Pin faces towards center. 2) With trampoline loosened, force hulls apart and place bow spreader in position on pins installed on bows 1 I I 3) With swivel cleat mounted to plate, install jib sheet jam cleat plate under existing trampoline hook* as shown. This is installed under center of three tramp hooks. Use the upper two of four holes in the plate. (*For installation on Club Wave see page two...) NOTE: Some very early model boats will require installation of an inspection port to access n

+33 494 08 78 78 - Fax +33 494 08 13 99 2 Hobie FX-One : Eclate de pieces detachees / Illustrated part guide/Explosionszeichnung (2003-2004) 3 15 16 17 13 1 - 99220930 (x10): Vis TH 8x30 casting Cast.bolt Schraube Gu.t. 2 - 99220750 (x10): Rondelle plate Washer Unterlegscheibe 3 - 17000010: Casting superieur Gouv. Upper rudder casting Oberes Rudergehause 4 - 18062148: Bras gouv.droit complet Tiller arm right complete Ruderarm rechts komplett 18062147: Bras gouv.gauche complet Tiller arm left com