o o @ustemer He_p L_n. t °8@@°843°1682 Safety _nstructions KnstatJation Operation Maintenance Parts List Espa_oi Sears, Roebuck and Co=, Hoffman Estates, mL60179 USA Part No. 1372!910001 GENERAL SAFETY INSTRUCTIONS !4. REMOVE ADJUSTING KEYS AND WRENCHES. SECTION PAGE From the habit of checking to see that keys and BEFORE USING THE DRILL PRESS adjusting wrenches are removed from the t0ol before Warranty ................... " ..... 2 turning "ON". Product Specifications ........... ...............

358.745290 • Safety • Assembly • Operation • Maintenance • Espar_ol Read and follow all Safety Rules and Operating WARNING: Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon-Sat; 10 am-7 pm, Sun • 1-800-235-5878 (Hours listed are Centra, Time) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 530164371 11/7/03 Warranty Statement 2 Parts Available Safety Rules 2 Storage 9 AssemblyOperationMaintenance 5 6 8 Troubleshooting S

TOWING • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. • Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes. • Never allow children or others in or on towed equipment. • On slopes, the weight of the towed equipment may cause loss of traction and loss of control. • Travel slowly and allow extra distance to stop. V. SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or

CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. Connect the other end of the bell wire to the two opener terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the push button control. Use insulated staples (not supplied) to secure bell wire between receiver and ope

3. Fill pump and suction pipe with water. Figure 9 -Run Ten Minutes Or Less If no water is produced within 10 minutes, stop pump, release all pressure, remove priming plug, refill and try again. [AWARNING] Hazardous pressure and risk of explosion and scalding. If pump is run continuously at no flow (that is, with discharge shut off or without priming), water may boil in pump and piping system. Under steam pressure, pipes may rupture, blow off of fittings or blow out of pump ports and scald anyon

1732150 Revision 00 Rev. Date 10/2005 TP 100-4240-00-CS-SN 5/14 Series Mfg. No. Description 1694910 Model 5/14, 5.5HP Simplicity Chipper / Shredder 1694898 Model 5/14, 5.5HP Simplicity Chipper / Shredder (CE) 7085637 Model SAC55140BV, 5.5HP Snapper Chipper / Shredder 7800070 Model E55140BV, 5.5HP Snapper Chipper / Shredder (CE) 8/14 Series Mfg. No. Description 1694678 Model 8/14, 8HP Simplicity Chipper / Shredder 1 Table of Contents Troubleshooting & Repair.................................17 Tro

Using a dull blade will place a heavy load on your saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available. Gum and wood pitch hardened on blades will slow your saw down. Use gum and pitch remover, hot water, or kerosene to remove these accumulations. Do not use gasoline. BLADE GUARD SYSTEM The lower blade guard attached to your circular saw is there for your protection and safety. It should never be altered for any reason. If it becomes dama

plate is located on the frame. Record these numbers in the spaces below and retain for future reference. Model No. Type Serial No. Part No. D26052-023-0 BEFORE ASSEMBLY 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the high pressure hose from the gun. TO ASSEMBLE HOSE REEL 1. Attach handle to flange assembly. NOTE: Screws must be inserted from the inside of hose reel and secured with nuts on the outside a

Siesta Removedora de nieve Craftsman se usa para prop6sitos comerciales o de arrendamiento, esta garantia es vdlida durante 90 dfas a partir de la fecha de compra. Esta garantfa no cubre Io siguiente: • Elementos fungibles los cuales se gastan durante el uso normal, tales como bujfas, correas de transmisi6n y clavijas de seguro por esfuerzo codante. • Reparaciones necesarias debido al abuso o negligencia del operador, incluyendo cigt_eSales doblados y ia falta de mantenimiento del equipo de acue

, No ponga las manos o los pies cerca o debajo de las partes rotatorias. Mantengase siempre lejos de la abertura de la descarga. * Permita que solamente las personas responsables que est_n familiarizadas con las instrucciones operen la maquina. , Despeje el Area de objetos tales como piedras, juguetes, alambres, huesos, palos, etc. que pueden ser recogidos y lanzados por las cuchillas. , AsegOrese que el Area no se hallen personas, antes de segar. Pare la maquina si alguien entra en el Area. , N