Service or maintenance performed by unqualified personnel could result in a risk of injury. 24.,When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. USBOOS-l Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rate

Un cable de calibre inferior ocasionara una caida en la tension de linea que resultara en una perdida de potencia y recalentamiento. La Tabla 1 muestra el tamano correcto a utilizar dependiendo de la longitud del cable y el amperaje nominal indicado en la placa de caracteristicas. Si no esta seguro, utilice el siguiente calibre mas alto. Cuanto menor sea el numero de calibre, mas corriente podra conducir el cable. 22 Tabla 1. Calibre minimo para el cable Tabla 1. Calibre minimo para el cable Vol

A list of the Factory Service Center locations and phone numbers is provided on page 24 for your convenience. 21 LIMITED WARRANTY - California Only - Makita U.S.A., Inc. a distributor of utility and ¡awn and garden equipment in the U.S., warrants to the owner of 1995 and later utility and/or lawn and garden equipment engines that the engine 0) has been designed, built, and equipped at the time of manufacture so as to conform with the applicable regulations of the California Air Resources Boa

Para obtener el rendimiento y satisfaccion maximos de la motosierra STIHL, es importante que lea, comprenda y respete las medidas de seguridad y las instrucciones de uso y mantenimiento dadas en el capitulo "Medidas de seguridad y tecnicas de uso" , antes de usar su motosierra. Para obtener informacion adicional, visite Comuniquese con su representante de STIHL o el distribuidor de STIHL para su zona si no se entiende alguna de las instrucciones dadas en el presente manual. .Advertencia! Dado qu

Don't force small tool or attachment to do the job of a heavy-duty tool. Don't use tool for purpose not intended. 7. DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair. 8. USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. caoutchouc et les chaussures anti-dérapantes sont conseillés si vous travaillez de

When the tree hangs or for some other reason does not fall completely, set the saw aside and pull the tree down with a cable winch, block and tackle or tractor. If you try to cut it down with your saw, you may be injured. Sectioning Method WARNING! Felling a tree that has a diameter greater than the length of the guide bar requires use of either the sectioning or plunge-cut method. These methods are extremely dangerous because they involve the use of the nose of the guide bar and can result in k

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the switch lever is in the neutral position, the switch trigger cannot be pulled. Selecting action mode Rotation with hammering (Fig. 4) For drilling in concrete, masonry, etc., depress the lock button and rotate the change lever so that the pointer points to the H symbol. Use a tungsten- carbide tip

SPECIFICATIONS Model 2012NB Cutting width 304 mm (12”) Max. cutting depth 3.0 mm (1/8”) of stock width less than 150 mm (5-7/8”) 1.5 mm (1/16”) of stock width from 150 mm (5-7/8”) to 240 mm (9-1/2”) 1.0 mm (3/64”) of stock width from 240 mm (9-1/2”) to 304 mm (12”) Feed rate /min 8.5 m (27.9 ft.) /min. Table size (W x L) 304 mm x 771 mm (12” x 30-3/8”) No load speed (RPM) 8,500 /min. Dimensions ( W x L x H ) 483 mm x 771 mm x 401 mm (19-1/64” x 30-3/8” x 15-25/32”) Net weight 27 kg (59.5 lbs) •

MAC700 MAC2400 MAC5200 Horsepower 2 2.5 3 SCFM @ 40 PSIG 3.8 4.8 6.9 SCFM @ 90 PSIG 3.3 4.2 6.5 Cut-In Pressure 100 PSI 100 PSI 110 PSI Cut-Out Pressure 130 PSI 130 PSI 140 PSI Bore 47 mm 51 mm 47 mm Stroke 44 mm 44 mm 44 mm Voltage -Single Phase 120 120 120 Motor RPM 1720 1720 3420 Amperage @ max pressure 12.4 12.3 13.8 Tank Size 2.6 Gallon 4.2 Gallon 5.2 Gallon CSA/US Listed Yes Yes Yes SPECIFICATION CHART Minimum Circuit Requirement: 15 AMPS * A circuit breaker is preferred. Use only a fuse o