Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. . WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building; • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. . Installation and service must be performed by a qualified installer, s

A hood must be installed when mantle is installed at 12” from fireplace opening. These fireplaces are U. L.® listed for use with “S” Series chimney system components. 400BWBA and 500BWBA Series Radiant Type 400BWBCA and 500BWBCA Series Circulating Type CONTENTS CONGRATULATIONS! You have chosen the finest wood burning fireplace available. Your fireplace has been designed for years of heating and viewing enjoyment. Please take time to read this entire manual before installing or operating your fir

The appliance will malfunction or the valve will be damaged. CAUTION Electrical connections should only be performed by a qualified, licensed electrician. Main power must be off when connecting to main electrical power supply or performing service. All wiring shall be in compliance with all local, city, and state codes. The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code ANSI / NFPA 70 (l

10 61D0008 61D0008 11 8" Min. 6" Min. Brick or Stone from Top of Platform Brick or Stone Hearth Extension 52" (400 Models) 66" (500 Models) 16" Min. (400 Unit) 20" Min. (500 Unit) 8" Min. 6" Min. Brick or Stone from Top of Platform Brick or Stone Hearth Extension 52" (400 Models) 66" (500 Models) 16" Min. (400 Unit) 20" Min. (500 Unit) FLOOR PROTECTION INSTALLING FIREPLACE ON COMBUSTIBLE FLOOR If fireplace is installed on a combustible floor, protect the floor area either side of the fireplace o

Cover the logs with ashes. A “banked” fire will hold glowing coals for 8-10 hours, thereby saving a fire for later use. 34 61D0008 FIREPLACE OPERATION WOOD VS. FOSSIL FUELS Compared to fossil fuels, a full cord of dry hickory weighs about two tons and is approximately equal in heating value to a ton of hard coal. On a per pound basis, heavy hardwoods have about half the heating value of coal. The table below shows the relative densities and heat values of a variety of dry woods. Varieties at the

This permits flexibility in planning your installation. See Figure 23 for typical installation methods. Review the precautions and recommendations in this manual pertaining to outside combustion air installation. Glass doors should be installed to receive the maximum benefit from your fireplace. For large fires, the maximum heating benefit from the fireplace will be obtained with the doors open due to the high amount of radiant heat being emitted out of the front opening of the fireplace. With

Overlap the ends of the collar until it is tight against the chimney. Bend the free end of the collar back over the loops to hold the storm collar securely together. CAUTION Use pliers and wear gloves when Trim off the excess ends of the storm collar. handling the storm color The edge of 8. Slide storm collar down snugly against the flashing until the storm color is sharp. If you are not the excess mastic left in step six is forced up into crack careful, you could cut your hands. between the sto

Rev 1 03/03 CONGRATULATIONS! You have chosen the finest wood burning fireplace available. Your fireplace has been designed for years of heating and viewing enjoyment. Please take time to read this entire manual before installing or operating your fireplace. TABLE OF CONTENTS Listing and Code Approvals........................................................................................................................1 Important Information.......................................................

OFFSET INSTALLATION SEQUENCE 1. Determine the location and amount of offset required, then select the combinations of chimney sections and elbows required from the offset chart. Refer to Table 2. 2. Install the first elbow by placing the crimped end into the mating part of the fireplace or chimney section. Push down until the outside or inlet air duct of the elbow overlaps and the snaps lock the elbow into the fireplace or chimney section. 3. Nail the support straps to the framing member with a

INSTALL AN UNVENTED GAS LOG SET INTO FIREPLACE. 53D9041. Rev 1 03/03 CONGRATULATIONS! You have chosen a fine woodburning fireplace. Your fireplace has been designed and built for years of heating and viewing enjoyment. Please take time to read this entire manual before installing or operating your fireplace. TABLE OF CONTENTS LISTING AND CODE APPROVALS.................................................................................................................................................