commend Impedance in Stereo Fuse Size S/N THD Frequency Response Dimensions L x W x H 222sx 22 x 2 2ohm 15 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 8.5" x 8.5" x 2.25" 230sx 30 x 2 2ohm 25 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 8.5" x 8.5" x 2.25" 250sx 50 x 2 2ohm 30 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 10" x 8.5" x 2.25" 275sx 75 x 2 2ohm 35 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 11" x 8.5" x 2.25" 2125sx 125 x 2 2ohm 40 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 17" x 8.5" x 2.25" 2150sx 15

Couple the terminals with a standard car stereo output system wither common ground or floating ground type originally output to speakers. The speaker wires of the car stereo should be connected to "L" and "R" terminals respectively, if the car stereo comes out with three wires only, connect the "COMMON" wire to both "L-" and "R-" input of the amplifier. Note: High and Low impedance input can’t be used at the same time. 3. INPUT GAIN CONTROL: When you connect your radio or equalizer to the amp

When using stereo, bridge, mono function, the connect model must be same than model switch selected. When output high-power signal continuously, the amplifier should be has speedup in the cooling fan, it may be have low noise produce in this equipment, it is normally. The general gain of the amplifier can be adjust by gain knob, the input level have 0.77V, 1.4V, full-power out and fixed 26dB gain 3 band should be selected. Donr vent of rear panel. When clear-up the cover of the equipment, you mu

Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service.The Pyle MARINE Class-D amplifier has been designed using the latest in electronic technology available today. This mono subwoofer amplifier is the result of advanced high speed switching technology that overcomes the less-efficient Class-D design. the Pyle MARINE Class-D amplifier reflects your true appreciation for powerful bass reproduction in the mobile environmen

Consulte la seccion Seleccion de ubicaciones de montaje de esta guia para ver informacion detallada. Paso 2. Decida que configuracion de sistema va a tener su amplificador. Para ver sugerencias de sistema, consulte la seccion Conexiones de altavoz de esta guia. Paso 3. Encamine todos los cables desde la ubicacion del amplificador hasta los altavoces, la unidad fuente y la bateria. No conecte la bateria en este momento. Pase los cables de altavoz, alimentacion y RCA lo mas lejos posible del siste

It has an RCA input and can be run off of phantom power through the din cable or can be wired directly. The Subwoofer output has level and crossover frequency adjustments. Technical Information -Main Volume control effects all outputs -Subwoofer volume effects volume of sub out only. -For the Three EQ Controls, the outer knobs offer frequency adjustments and inner knobs offer +/- 12dB of boost/cut. -The gain controls on the top of the PSW adjust the input sensitivity. S' (Specifications

Ground (10.5-16V) 270 x 36 x 330 10.63 x 1.42 x 13 features and controls 18dB 0dB HPF LPF FULL HPF LPF FULL 18dB 0dB BASS BOOST X-OVER BASS BOOSTX-OVER CH 1/2 CH 3/4 4 ch amp PLA-4120 PLA-4120 9 electrical connections 2 ch amp • PLA-2230 • PLA-2260 PLA-2230 PLA-2260 10 PLA-4120 electrical connections PLA-4120 electrical connections 4 ch amp PLA-4120 11 stereo input connections 2 ch amp • PLA-2230 • PLA-2260 12 PLA-2230 PLA-2260 mono input connections 2 ch amp • PLA-2230 • PLA-2260 13 PLA-2230 PL

This warranty is limited to the original retail purchase. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Pyle. To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236-6948 to obtain a Return Authorization number. This R.A.# must appear on the outside of your package and on all paperwork relating to your return. When returning a product to us for warranty service it

And the ground cable gauge should be the same as the +12V DC. * Connect the +12V Power terminal to the battery (+) position terminal. An in-line fuse must be installed in the +12V power cable near the battery less than 50mm. Without one, an accidental short circuit could pose a fire hazard and damage your amplifier. Connect the fuse holder to battery, however, do not install fuse at this time. * Connect the GROUND Power terminal directly to the battery (-) position terminal or the car chassis.

0hz, and 6dB of boost at 10Khz. The DIN input: The din input can be used to power Orion crossovers and equalizers with the same style DIN plug. Amp Model 4ohm Power Lowest Recommend Impedance in Stereo Fuse Size S/N THD Frequency Response Dimensions L x W x H 222sx 22 x 2 2ohm 15 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 8.5" x 8.5" x 2.25" 230sx 30 x 2 2ohm 25 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 8.5" x 8.5" x 2.25" 250sx 50 x 2 2ohm 30 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 10" x 8.5" x 2