Running the deck out of level will result in poor cut quality and increased belt wear. Fig. 2 Part No 510267 Form No F031607A 9 HW Owner’s Manual PROPULSION This unit is self-propelled, and is controlled by a lever control. To engage the wheel drive, pull up and squeeze it against operator's handle. The drive is disengaged by releasing this lever.(See Fig. 3 & 3.1) GROUND SPEED can be varied by selecting a higher or lower gear using the gearshift lever on top of the handle (See Fig. 4). Under mo

830180 1 830180 1 830180 1 10 Belt Traction Drive 500119 1 500119 1 500119 1 11 Plate Pivot Idler / Shifter 500122 1 500122 1 500122 1 12 Shifter Pivot WA 500169 1 500169 1 500169 1 13 Pulley Idler 800260 1 800260 1 800260 1 14 Wheel & Tire 16" AG SP LH 500103 1 500103 1 500103 1 15 Wheel & Tire 16" AG SP RH 500104 1 500104 1 500104 1 16 Arm Idler WA 500170 1 500170 1 500170 1 17 Cable Clutch Blade BC2400 500259 1 500259 1 500259 1 18 Cable Clutch Drive BC2400 500146 1 500146 1 500146 1 19 Bar S

INTAKE HOSE: Hose mounting assembly must be properly attached to vac housing and safety switch must be engaged before engine will start. Note: Any damage to the switch or wiring harness will prevent engine from starting. CHOKE: Located on the vac housing as part of the engine control panel. THROTTLE: Move throttle control to fast position. KEY SWITCH: Turn to start position until engine begins to fire, immediately release the key to the run position. Note: Do not hold key in start position more

Move equipment away from spill until gasoline has completely evaporated. DO NOT operate engine without a muffler. Inspect muffler periodically and replace if necessary. If equipped with muffler deflector, inspect deflector periodically and replace if necessary. DO NOT operate engine with grass, leaves, or other combustible material near the muffler. DO NOT touch muffler, cylinder or cooling fins while engine is running. Contact with hot surfaces may cause severe burns. DO NOT operate equipment w

D E S C R IP T IO N K D 6 1 2 P a rt N o . Q T Y K D 5 1 2 H C P a rt N o . Q T Y K D 51 2 H C S P a rt N o . Q T Y * Denotes standard hardware item that may be purchase d locally. 1 P R O D E B R IS B A G (s e rv ic e ) 8 90 3 0 5 1 8 9 0 02 3 1 8 9 00 2 3 1 2 3 4 N U T L O C K (1 /4 -2 0 ) *8 16 0 0 0 1 7 *8 1 60 0 0 1 7 *8 16 0 0 0 1 7 5 S C R E W C A P ( 1 /4 -2 0 x 1 -1 /2 H E X ) *8 04 1 0 0 8 8 *8 0 41 0 0 8 8 *8 04 1 0 0 8 8 6 H A N D L E A S S ’Y (inc l. ite m s 4 (5),5 (5),1 1 (2),7 5

directions using calibrate vibration te^. ^pipn^t. Tests were performs! on 05/03/94 under the conditions listed: GENERAL CONDI- _partly Cloudy_ TION:_ TEMPERATURE: WIND SPEED: WIND DIRECTION: HUMIDITY: 60 * F (15.5 C) 5 MPH (8kmh) BAROMETRIC PRESSURE :29.8’’ (757mm Hg) Form No. F021695C 70 70 TABLE OF CONTENTS SAFETY INSTRUCTIONS 2 GENERAL SAFETY . . . . 3 ASSEMBLY....... 3 PARTS BAG & CONTROLS 4 LABELS ........ 4 OPERATION 5 PARTS DRAWING & LIST 7 6 MAINTENANCE 8 TROUBLESHOO

Shreds leaves, dramatically reducing total volute. HOSE KITS For vacuuming in hard to reach areas. HeavyDuty Vacuum Hose Kit P/N 900943. 4" (102mm) x 10' (3.05m) Homeowners Vacuum Hose Kit P/N 900942. 4" (102mm) x 1Û' (3.05m) NOZZLE WEAR PLATES P/N 900810. Extends nozzle life when used along curbs and hard surfaces. STANDARD FELT DEBRIS BAG P/N 900803. Standard on KD medals. For dusty ccnditicns. OPTIONAL DEBRIS BAGS TURF DEBRIS BAG P/N 900806 for use in leaves and grass in ron-dusty c

1. Disconnect spark plug wire. 2. Remove the deck belt cover. 3. Support front of unit to allow access to underside of the machine near the engine. Note: Unit is heavy. Be sure support is adequate to prevent personal injury. 4. Observe the orientation of the belt fi ngers (Item 71) under the engine. 5. Remove the 4 engine mount bolts (Item 48) 6. Remove the left and right belt fi ngers (These fi ngers are interchangeable). 7. Observe the orientation of the belt fi nger (Item 90) on idler (Item 9

F112003A 33" TRIPLE BLADE MOWER COMMERCIAL Page 1 of 20 Operator Owner's Manual Thank You f o r S e l e c t i n g 1 3 Specifi cations The Powerful Self-Propelled Billy Goat Mower UNIT SIZE: OVERALL LENGTH - 57"(1.45 m) OVERALL WIDTH - 43" (1.09 m) OVERALL HEIGHT - 47" (1.19 m) FM3300IN ,FM3300INE, FM3300INB ,FM3300INEB FM3300IN FM3300INE FM3300INB FM3300INEB Engine: HP 13.0 HP (9.7 kW) 13.0 HP (9.7 kW) 13.0 HP (9.7 kW) 13.0 HP (9.7 kW) Engine:Type B&S INTEK OHV B&S INTEK OHV B&S INTEK OHV B&S IN

Your BILLY GOAT ® FORCE Blower was shipped in one carton, completely assembled except for the Upper Handle Assembly and Front Diverter. Mounting hardware for the Upper Handle Assembly can be found in the parts bag. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the unit by cables. PUT OIL IN ENGINE BEFORE STARTING PARTS BAG & LITERATURE ASSY Warranty card P/N-400972, Owner’s Manual P/N-440021, Declaration o