TABLE of CONTENTS TABLE of CONTENTS PG 3-4 INTRODUCTION Warranty General Instructions General Information Care of Glass Doors, Catalytic Tiles & Plated Parts 5-12 INSTALLATION Combustion and Ventilation Air Provisions Determining Confined or Unconfined Space Gas Installation Framing Dimensions Peninsula Installation Procedure Open End Installation Procedure See-Thru Installation Procedure Island Installation Procedure 13-15 FINISHING Log Placement Glowing Embers Charcoal Embers Mantle Installati

Theflamemaynotappearyellowimmediately;allow15to30 minutes for the final flame colour to be established. figure 69 figure 68 AIR SHUTTER OPENING W4 5-0536 / C / 09.06.06 8 REPLACEMENTS Contact your dealer for questions concerning prices and avail-1. MoDel & SeRIal nuMBeR oF FIReplace ability of replacement parts. Normally all parts can be ordered 2. InStallatIon Date oF FIReplace through your Napoleon dealer or distributor. 3. paRt nuMBeR When ordering replacement parts always give the following

- 21 3/4” to top of fireplace opening. FIGURE 28 FIGURE 29 FIGURE 30 It is best to frame your fireplace after it is positioned and the vent system is installed. Use 2x4’s and frame to local building codes. Note: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the fireplace body, it is recommended that the walls of the fireplace enclosure be “finished” (ie: drywall/sheetrock), as you would finish any other outside wall of a home. This will ensure t

Ensure that both spacer and shield maintain the required clearance to combustibles. Once the vent pipe is installed in its final position, apply sealant between the pipe and the firestop spacer. 3. In the attic, after the pipe has been installed, slide the vent pipe collar down to cover up the open end of the shield and tighten. This will prevent any materials, such as insulation, from filling up the 1" air space around the pipe. FIGURE 22 FOR FORFORFORFORFOR SAFE SAFESAFESAFESAFESAFE AND ANDAND

psig (3.5 kPa). The stove, when installed with a blower, must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1996 NATIONAL ELECTRICAL CODE in the United States. The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug. GENERAL INFORMATION FOR YOUR SATISFACTION, THIS STOVE HAS BEEN TES

TAMPERING WITH THE SWITCH CAN RESULT IN CARBON MONOXIDE (CO) POISONING AND POSSIBLE DEATH. MODEL GS60 ONLY:VENTING ACTION CHECK A CHECK FOR CORRECT VENTING ACTION MUST BE MADE BEFORE THE INSTALLED STOVE IS LEFT WITH THE CUSTOMER. Test in the following manner: 1. Close all doors and windows in the room / start exhaust fans in the home / turn fireplace blower off (if equipped). 2. Set controls to "high" and light the unit. 3. Wait 5 minutes. Light a match and extend it 1" into the hole located abo

A 5-10 second total light-up period is satisfactory. If ignition takes longer, consult your Napoleon dealer/distributor. 7. Check that the door gasketing is not broken or missing. Replace if necessary. W415-0158 / E / 02.19.04 BLOWER INSTALLATION BLOWER INSTALLATION 1. Ensure that the access cover plate has been installed. For location, see Figure 30. 2. Remove the on/off switch bracket and the cover plate below it. The switch spacers and cover plate may now be discarded. 3. Decide which side of

Dry fi t the fi restop assembly before proceeding to ensure the brackets on the rear surface fi t within the horizontal framing. As an alternative to framing, the vent pipe can be enclosed in the wall using Napoleon® vent sleeve VS47KT. NOTE: THE FIRESTOP ASSEMBLY MUST BE INSTALLED WITH THE VENT SHIELD TO THE TOP. The length of the vent shield may be cut shorter for combustible walls that are less than 8 1/2" thick but the vent shield must extend the full depth of the combustible wall. 1. Apply

- Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier’s instructions. - If you cannot reach your gas supplier, call the fire department. - Installation and service must be performed by a qualified installer, service agency or the supplier. INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, persona

HINT: If glass falls into cup and surrounds the orifice, insert a clean bag into a vacuum cleaner and vacuum out glass embers or replacement glass embers can be ordered from Wolf Steel Ltd. Note: The distribution of clear glass embers over the burner tube will influence the flame height. W415-0661 / C / 02.20.08 OPTIONAL BLOWER INSTALLATION OPTIONAL BLOWER INSTALLATION BGD36CF(G) ACCESSING THE BLOWER 1. Remove the valve access door. 2. Open the main door. 3. Carefully remove the logs. 3a. (BGD36